ADC AD-26 Retain This Manual In a Safe Place For Future Reference, Important Note to Purchaser

Page 2

Retain This Manual In A Safe Place For

Future Reference

Please read this manual carefully to thoroughly familiarize yourself with the Phase 5 Coin computer system features, operational instructions, and programming characteristics. This manual contains important information on how to use ALL the features of your new ADC dryer in the safest and fastest way.

American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation.

We have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or discontinue models.

! WARNING

Proposition 65

Use of this product could expose you to substances from fuel combustion that contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.

“IMPORTANT NOTE TO PURCHASER”

Information must be obtained from your local gas supplier on the instructions to be followed if the user smells gas. These instructions must be posted in a prominent location near the dryer.

Image 2
Contents Phase Coin USER’S Manual Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserTable Of Contents Programming Instructions For dryer models AD-26/AD-295 Only Motor Circuit IndicatorFor all dryer models except AD-26/AD-295 and AD-540/WDA-540 Introduction Time for Amount to Start Cool Down Time Cool Down TemperaturesFree DRY Mode ANTI-WRINKLEBatterybackup Optional Temperature DisplayDiagnostics Automatic DrytimeFill D. Displayand CodesClcc FLSPPF LCCPloc PushTimed Mode Operating InstructionsAutomatic Mode Patent no ,827,627 Free DRY Mode Right Coin Count rCC/LEFT Coin Count LCC Temperature Display ModeProgram Selection Automatic Review of Program Location Timed Mode tInE PL01 Temperature Conversion StatusAutomatic Mode AUtO Patent No ,827,627 BUZZ/TONE bUZ Free DRY Mode FrEEANTI-WRINKLE Program Grd Flash Display Status FLS Coin Mode CoinBAD Coin Reset bCrS BAD Coin Lockout Status bCLODual Coin Accumulative Time AtInSingle Coin PL10 rCdE PL11 tFAS PL12 AtSt Dual Coinacceptor Accumulative Coin ACOnSingle Coin Acceptor PL02 Percent DRY PdrY PL03 High Temperature HIFRotational Safe Guard OPTIONALnSEn PL05 LOW Temperature LOF PL07 Permanent Press PPFPL12 Amount to Start AtSt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL13 Minimum Amount for Additional Time AFAtPL17 a and b Factors PL15 ANTI-WRINKLE TimingPL16 Active Guard Time AGt Programming Instructions Introduction to ProgrammingProgramming Flowcharts Dryer Off Power On Display Reads No cycle in progress ButtonExample And/orCycle In Progress Temperature Display ModeProgramming Left Coin Count Right Coin Count Program Location 01 PL01 Press Perm Press key, otherwise Display will read anti-wrinkleGuard program status. If no change Press HI or LO keys and thenFLS AtIn LO Temp Continue HI Temp Perm Press PL03 Program Location 02 PL02PL02 Perm Press Pdry Program Location 03 PL03 HIFTime Decrease Time Increase HI Temp cool down temperature/timeProgram Location 04 PL04 Program Location 05 PL05 Time Decrease LO Temp cool down temperature/timeProgram Location 06 PL06 Program Location 07 PL07 PPFPerm Press Cool Down Temperature/Time Program Location 08 PL08Program Location 09 PL09 PL09 Perm Press LCdEProgram Location 10 PL10 Right Coin DenominationProgram Location 11 PL11 Program Location 12 PL12 Proceed to next location To be changed PL12 Perm Press AtStProgram Location 13 PL13 Proceed to next location To be changed PL13 Perm Press AFAtProgram Location 14 PL14 Maximum Time for Auto DryProgram Location 15 PL15 Anti-Wrinkle TimingProgrammable 1 to Factor Decrease Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Factor IncreaseFactory Preset PROGRAMS/PARAMETERS Single Coin only TFAS Time for amount to start 10 minutes Dual Coin onlyLCdE Left coin denomination 10¢ AFAt Amount for additional time 10¢PPCd Temperature 80, Time 3 minutes HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98%RCdE Right coin denomination 10¢ PL06 LOCd Temperature 80, Time 2 minutesPL08 PPCd Temperature 80, Time 3 minutes Phase 5 Coin System Diagnostics Diagnostic L.E.D. Failure CodesE.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08