ADC AD-540, AD-295 Display will read anti-wrinkle, Guard program status. If no change, Perm Press

Page 35

nGrd

LO Temp

Grd

bUZ

LO Temp

nbUZ

Coin

LO Temp

FrEE

		Display will read anti-wrinkle
Continue		(guard) program status. If no change,
		press “Perm Press” key, otherwise
		press “Perm Press” key, otherwise
		press “HI” or “LO” keys and then
		press “HI” or “LO” keys and then
Perm Press		“Perm Press.”

or			Grd
or
HI Temp		LO Temp	HI Temp
HI Temp
or			nGrd
or
Perm Press			If guard (Grd) was
Perm Press			selected, display will read
			tone/buzzer status. If no
			change, press “Perm
or		nbUZ	Press” key, otherwise
or			press “HI” or “LO” keys
			press “HI” or “LO” keys
			and then “Perm Press”
HI Temp	LO Temp	HI Temp	key.
or		bUZ
or
Perm Press			Display will read vend
			status, either “Coin”
or			(coins required to start)
or		FrEE	or “FrEE” (no coins
		FrEE	or “FrEE” (no coins
			required). If no change,
			press “Perm Press”
HI Temp	LO Temp	HI Temp	otherwise press “HI” or
			“LO” keys and then
or		Coin	“Perm Press” key.
or		Coin
Perm Press
Continue

33

Image 35

Contents Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferenceTable Of Contents Programming Instructions For dryer models AD-26/AD-295 Only Motor Circuit IndicatorFor all dryer models except AD-26/AD-295 and AD-540/WDA-540 Introduction Time for Amount to Start ANTI-WRINKLE Cool Down TemperaturesFree DRY Mode Cool Down TimeAutomatic Drytime Temperature DisplayDiagnostics Batterybackup OptionalFLS D. Displayand CodesClcc FillPush LCCPloc PPFOperating Instructions Timed ModeAutomatic Mode Patent no ,827,627 Free DRY Mode Right Coin Count rCC/LEFT Coin Count LCC Temperature Display ModeProgram Selection Automatic Review of Program Location Timed Mode tInE PL01 Temperature Conversion StatusAutomatic Mode AUtO Patent No ,827,627 BUZZ/TONE bUZ Free DRY Mode FrEEANTI-WRINKLE Program Grd BAD Coin Lockout Status bCLO Coin Mode CoinBAD Coin Reset bCrS Flash Display Status FLSDual Coin Accumulative Time AtInSingle Coin PL10 rCdE PL11 tFAS PL12 AtSt Dual Coinacceptor Accumulative Coin ACOnSingle Coin Acceptor PL02 Percent DRY PdrY PL03 High Temperature HIFRotational Safe Guard OPTIONALnSEn PL07 Permanent Press PPF PL05 LOW Temperature LOFPL13 Minimum Amount for Additional Time AFAt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL12 Amount to Start AtStPL17 a and b Factors PL15 ANTI-WRINKLE TimingPL16 Active Guard Time AGt Introduction to Programming Programming InstructionsProgramming Flowcharts Button Dryer Off Power On Display Reads No cycle in progressAnd/or ExampleCycle In Progress Temperature Display ModeProgramming Left Coin Count Right Coin Count Program Location 01 PL01 Press HI or LO keys and then Display will read anti-wrinkleGuard program status. If no change Press Perm Press key, otherwiseFLS AtIn LO Temp Continue HI Temp Perm Press PL03 Program Location 02 PL02PL02 Perm Press Pdry HIF Program Location 03 PL03Time Decrease Time Increase HI Temp cool down temperature/timeProgram Location 04 PL04 Program Location 05 PL05 Time Decrease LO Temp cool down temperature/timeProgram Location 06 PL06 PPF Program Location 07 PL07Program Location 08 PL08 Perm Press Cool Down Temperature/TimePL09 Perm Press LCdE Program Location 09 PL09Right Coin Denomination Program Location 10 PL10Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13Maximum Time for Auto Dry Program Location 14 PL14Anti-Wrinkle Timing Program Location 15 PL15Factor Increase Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Programmable 1 to Factor DecreaseFactory Preset PROGRAMS/PARAMETERS Single Coin only AFAt Amount for additional time 10¢ Dual Coin onlyLCdE Left coin denomination 10¢ TFAS Time for amount to start 10 minutesNSEn Rotational sensor not selected PdrY Percent Dry 98% HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes PPCd Temperature 80, Time 3 minutesRCdE Right coin denomination 10¢ PL06 LOCd Temperature 80, Time 2 minutesPL08 PPCd Temperature 80, Time 3 minutes Diagnostic L.E.D. Failure Codes Phase 5 Coin System DiagnosticsE.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08