ADC Learn About the Goodmans GDB1225DTR Remote for Clothes Dryers

Page 3

Table Of Contents
SECTION I
INTRODUCTION	4
Phase 5 Coin Microprocessor Controller (Computer) Features	4
SECTION II
L.E.D. DISPLAY AND CODES	8
SECTION III
OPERATING INSTRUCTIONS	10
A. Timed Mode	10
B. Automatic Mode (Patent No. 4,827,627)	11
C. Free Dry Mode	12
SECTION IV
PROGRAM SELECTION	13
Temperature Display Mode	13
Right Coin Count (rCC)/Left Coin Count (LCC)	13
Automatic Review of Program Location	14
PL01 - Temperature Conversion Status	15
Automatic Mode (Auto) Patent No. 4,827,627	15
Timed Mode (tInE)	15
Anti-Wrinkle Program (Grd)	16
Buzz/Tone (bUZ)	16
Free Dry Mode Cycle (FrEE)	16
Coin Mode (Coin)	17
Flash Display Status (FLS)	17
Bad Coin Lockout Status (bCLO)	17
Bad Coin Reset (bCrS)	17
AccumulativeTime (AtIn)	18
Accumulative Coin (ACOn)	20
Rotational Safe Guard - OPTIONAL (nSEn)	21
PL02 - Percent Dry (PdrY)	21
PL03 - High Temperature (HI° F)	21
PL04 - High Cool Down Temperature/Time (HIcd)	22
PL05 - Low Temperature (LO° F)	22
PL06 - Low Cool Down Temperature/Time (LOcd)	22
PL07 - Permanent Press (PP° F)	22
PL08 - Permanent Press Cool Down Temperature /Time (PPCd)	22
PL09 - Left Coin Slot Denomination (LCdE)	22
PL10 - Right Coin Slot Denomination (rCdE)	23

Image 3

Contents Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferenceTable Of Contents Programming Instructions Motor Circuit Indicator For all dryer models except AD-26/AD-295 and AD-540/WDA-540For dryer models AD-26/AD-295 Only Introduction Time for Amount to Start ANTI-WRINKLE Cool Down TemperaturesFree DRY Mode Cool Down TimeAutomatic Drytime Temperature DisplayDiagnostics Batterybackup OptionalFLS D. Displayand CodesClcc FillPush LCCPloc PPFOperating Instructions Timed ModeAutomatic Mode Patent no ,827,627 Free DRY Mode Temperature Display Mode Program SelectionRight Coin Count rCC/LEFT Coin Count LCC Automatic Review of Program Location PL01 Temperature Conversion Status Automatic Mode AUtO Patent No ,827,627Timed Mode tInE Free DRY Mode FrEE ANTI-WRINKLE Program GrdBUZZ/TONE bUZ BAD Coin Lockout Status bCLO Coin Mode CoinBAD Coin Reset bCrS Flash Display Status FLSAccumulative Time AtIn Single CoinDual Coin PL10 rCdE PL11 tFAS PL12 AtSt Accumulative Coin ACOn Single Coin AcceptorDual Coinacceptor PL03 High Temperature HIF Rotational Safe Guard OPTIONALnSEnPL02 Percent DRY PdrY PL07 Permanent Press PPF PL05 LOW Temperature LOFPL13 Minimum Amount for Additional Time AFAt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL12 Amount to Start AtStPL15 ANTI-WRINKLE Timing PL16 Active Guard Time AGtPL17 a and b Factors Introduction to Programming Programming InstructionsProgramming Flowcharts Button Dryer Off Power On Display Reads No cycle in progressAnd/or ExampleTemperature Display Mode ProgrammingCycle In Progress Left Coin Count Right Coin Count Program Location 01 PL01 Press HI or LO keys and then Display will read anti-wrinkleGuard program status. If no change Press Perm Press key, otherwiseFLS AtIn LO Temp Continue HI Temp Program Location 02 PL02 PL02 Perm Press PdryPerm Press PL03 HIF Program Location 03 PL03HI Temp cool down temperature/time Program Location 04 PL04Time Decrease Time Increase Program Location 05 PL05 LO Temp cool down temperature/time Program Location 06 PL06Time Decrease PPF Program Location 07 PL07Program Location 08 PL08 Perm Press Cool Down Temperature/TimePL09 Perm Press LCdE Program Location 09 PL09Right Coin Denomination Program Location 10 PL10Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13Maximum Time for Auto Dry Program Location 14 PL14Anti-Wrinkle Timing Program Location 15 PL15Factor Increase Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Programmable 1 to Factor DecreaseFactory Preset PROGRAMS/PARAMETERS Single Coin only AFAt Amount for additional time 10¢ Dual Coin onlyLCdE Left coin denomination 10¢ TFAS Time for amount to start 10 minutesNSEn Rotational sensor not selected PdrY Percent Dry 98% HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes PPCd Temperature 80, Time 3 minutesPL06 LOCd Temperature 80, Time 2 minutes PL08 PPCd Temperature 80, Time 3 minutesRCdE Right coin denomination 10¢ Diagnostic L.E.D. Failure Codes Phase 5 Coin System DiagnosticsE.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08