ADC WDA-540, AD-295, AD-26, AD-540 user manual Automatic Review of Program Location

Page 16

AUTOMATIC REVIEW OF PROGRAM LOCATION

This selection allows for the AUTOMATIC REVIEW of what the program locations are set (programmed) for, thereby eliminating the need to go into each and every Program Location (PL) manually for verification. By closing the Programming Switch (PS) with no cycle in progress, the light emitting diode (L.E.D.) display will read the temperature in the dryer. Then, by pressing the “LO TEMP” key, the L.E.D. display will read “PLOC” for 1-second. Then, the Phase 5 coin microprocessor controller (computer) will go into the Automatic Review Mode, the Program Location numbers (i.e., PL01, PL02, etc.) will not be shown and each parameter (i.e., “°FAr,” “tInE,” “Grd,” etc.) will be displayed for approximately 1-second each. The Automatic Review can be stopped/exited at any time by simply pressing the “PERM PRESS” key, at which time the L.E.D. display will read “0000” for 1-second and then return to the Temperature Display mode.

14

Image 16
Contents Phase Coin USER’S Manual Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserTable Of Contents Programming Instructions For all dryer models except AD-26/AD-295 and AD-540/WDA-540 Motor Circuit IndicatorFor dryer models AD-26/AD-295 Only Introduction Time for Amount to Start Cool Down Temperatures Free DRY ModeCool Down Time ANTI-WRINKLETemperature Display DiagnosticsBatterybackup Optional Automatic DrytimeD. Displayand Codes ClccFill FLSLCC PlocPPF PushTimed Mode Operating InstructionsAutomatic Mode Patent no ,827,627 Free DRY Mode Program Selection Temperature Display ModeRight Coin Count rCC/LEFT Coin Count LCC Automatic Review of Program Location Automatic Mode AUtO Patent No ,827,627 PL01 Temperature Conversion StatusTimed Mode tInE ANTI-WRINKLE Program Grd Free DRY Mode FrEEBUZZ/TONE bUZ Coin Mode Coin BAD Coin Reset bCrSFlash Display Status FLS BAD Coin Lockout Status bCLOSingle Coin Accumulative Time AtInDual Coin PL10 rCdE PL11 tFAS PL12 AtSt Single Coin Acceptor Accumulative Coin ACOnDual Coinacceptor Rotational Safe Guard OPTIONALnSEn PL03 High Temperature HIFPL02 Percent DRY PdrY PL05 LOW Temperature LOF PL07 Permanent Press PPFPL10 Right Coin Slot Denomination rCdE PL11 Time for Amount to Start tFASPL12 Amount to Start AtSt PL13 Minimum Amount for Additional Time AFAtPL16 Active Guard Time AGt PL15 ANTI-WRINKLE TimingPL17 a and b Factors Programming Instructions Introduction to ProgrammingProgramming Flowcharts Dryer Off Power On Display Reads No cycle in progress ButtonExample And/orProgramming Temperature Display ModeCycle In Progress Left Coin Count Right Coin Count Program Location 01 PL01 Display will read anti-wrinkle Guard program status. If no changePress Perm Press key, otherwise Press HI or LO keys and thenFLS AtIn LO Temp Continue HI Temp PL02 Perm Press Pdry Program Location 02 PL02Perm Press PL03 Program Location 03 PL03 HIFProgram Location 04 PL04 HI Temp cool down temperature/timeTime Decrease Time Increase Program Location 05 PL05 Program Location 06 PL06 LO Temp cool down temperature/timeTime Decrease Program Location 07 PL07 PPFPerm Press Cool Down Temperature/Time Program Location 08 PL08Program Location 09 PL09 PL09 Perm Press LCdEProgram Location 10 PL10 Right Coin DenominationProgram Location 11 PL11 Program Location 12 PL12 Proceed to next location To be changed PL12 Perm Press AtStProgram Location 13 PL13 Proceed to next location To be changed PL13 Perm Press AFAtProgram Location 14 PL14 Maximum Time for Auto DryProgram Location 15 PL15 Anti-Wrinkle TimingProgram Location 16 PL16 and Program Location 17 PL17 Maximum Active Anti-Wrinkle TimeProgrammable 1 to Factor Decrease Factor IncreaseFactory Preset PROGRAMS/PARAMETERS Single Coin only Dual Coin only LCdE Left coin denomination 10¢TFAS Time for amount to start 10 minutes AFAt Amount for additional time 10¢HICd Temperature 80, Time 2 minutes LOCd Temperature 80, Time 2 minutesPPCd Temperature 80, Time 3 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98%PL08 PPCd Temperature 80, Time 3 minutes PL06 LOCd Temperature 80, Time 2 minutesRCdE Right coin denomination 10¢ Phase 5 Coin System Diagnostics Diagnostic L.E.D. Failure CodesE.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08