ADC AD-295, WDA-540, AD-26, AD-540 user manual Right Coin Count

Page 33

C. RIGHT COIN COUNT

(No Cycle In Progress)

 

FILL

 

and/or

 

25

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Close Program Switch)

(Amount To Start)

HI Temp

70F

(Dryer Temperature Display)

LCC

HI Temp

rCC

Perm Press

0192

To cancel coin count

To cancel or delete

right coin count, HI Temp press “HI Temp” key.

Display will read

“CrCC (cancel right CrCC coin count).

Press “Perm Press”

Perm Press

key and display

 

will read “0000”

 

(coin count cancelled).

0000

 

Press “Perm Press”

Perm Press

key.

 

To retain coin count

Perm Press

0000

70F

To exit program mode open program switch

Press “HI Temp” key. Display will read “LCC” (left coin count).

Press “HI Temp” key. Display will read “rCC” (right coin count).

Press “Perm Press” key to display coin count.

Display will read actual coin count. I.E. 0192 = 192 units or coins.

To retain or save existing coin count press “Perm Press.”

Display will read “0000” for 1-second and then dryer temperature display.

31

Image 33
Contents Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferenceTable Of Contents Programming Instructions Motor Circuit Indicator For all dryer models except AD-26/AD-295 and AD-540/WDA-540For dryer models AD-26/AD-295 Only Introduction Time for Amount to Start Free DRY Mode Cool Down TemperaturesCool Down Time ANTI-WRINKLEDiagnostics Temperature DisplayBatterybackup Optional Automatic DrytimeClcc D. Displayand CodesFill FLSPloc LCCPPF PushOperating Instructions Timed ModeAutomatic Mode Patent no ,827,627 Free DRY Mode Temperature Display Mode Program SelectionRight Coin Count rCC/LEFT Coin Count LCC Automatic Review of Program Location PL01 Temperature Conversion Status Automatic Mode AUtO Patent No ,827,627Timed Mode tInE Free DRY Mode FrEE ANTI-WRINKLE Program GrdBUZZ/TONE bUZ BAD Coin Reset bCrS Coin Mode CoinFlash Display Status FLS BAD Coin Lockout Status bCLOAccumulative Time AtIn Single CoinDual Coin PL10 rCdE PL11 tFAS PL12 AtSt Accumulative Coin ACOn Single Coin AcceptorDual Coinacceptor PL03 High Temperature HIF Rotational Safe Guard OPTIONALnSEnPL02 Percent DRY PdrY PL07 Permanent Press PPF PL05 LOW Temperature LOFPL11 Time for Amount to Start tFAS PL10 Right Coin Slot Denomination rCdEPL12 Amount to Start AtSt PL13 Minimum Amount for Additional Time AFAtPL15 ANTI-WRINKLE Timing PL16 Active Guard Time AGtPL17 a and b Factors Introduction to Programming Programming InstructionsProgramming Flowcharts Button Dryer Off Power On Display Reads No cycle in progressAnd/or ExampleTemperature Display Mode ProgrammingCycle In Progress Left Coin Count Right Coin Count Program Location 01 PL01 Guard program status. If no change Display will read anti-wrinklePress Perm Press key, otherwise Press HI or LO keys and thenFLS AtIn LO Temp Continue HI Temp Program Location 02 PL02 PL02 Perm Press PdryPerm Press PL03 HIF Program Location 03 PL03HI Temp cool down temperature/time Program Location 04 PL04Time Decrease Time Increase Program Location 05 PL05 LO Temp cool down temperature/time Program Location 06 PL06Time Decrease PPF Program Location 07 PL07Program Location 08 PL08 Perm Press Cool Down Temperature/TimePL09 Perm Press LCdE Program Location 09 PL09Right Coin Denomination Program Location 10 PL10Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13Maximum Time for Auto Dry Program Location 14 PL14Anti-Wrinkle Timing Program Location 15 PL15Maximum Active Anti-Wrinkle Time Program Location 16 PL16 and Program Location 17 PL17Programmable 1 to Factor Decrease Factor IncreaseFactory Preset PROGRAMS/PARAMETERS Single Coin only LCdE Left coin denomination 10¢ Dual Coin onlyTFAS Time for amount to start 10 minutes AFAt Amount for additional time 10¢LOCd Temperature 80, Time 2 minutes HICd Temperature 80, Time 2 minutesPPCd Temperature 80, Time 3 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98%PL06 LOCd Temperature 80, Time 2 minutes PL08 PPCd Temperature 80, Time 3 minutesRCdE Right coin denomination 10¢ Diagnostic L.E.D. Failure Codes Phase 5 Coin System DiagnosticsE.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08