ADC AD-540 Dual Coin only, LCdE Left coin denomination 10¢, AFAt Amount for additional time 10¢

Page 55

B. DUAL COIN ONLY

For ALL dryer models except AD-26/AD-295 and AD-540/WDA-540. (For Dual Coin models AD-26/ AD-295 and AD-540/WDA-540refer to page 55).

PL01 -

°FAr

- Temperatures in Fahrenheit

 

tInE

- Timed mode

 

Grd

- Anti-wrinkle guard on

 

bUZ

- Anti-wrinkle guard buzzer (tone) on

 

Coin

- Coin(s) required to start

 

FLS

- Display will flash in intervals between “FILL” and “Amount To start”

 

bCrS

- Bad coin reset

 

AtIn

- Accumulative time

PL02 -

nSEn

- Rotational sensor not selected

PdrY

- Percent Dry - 97%

PL03 - HIOF

- 180°

PL04 -

HICd

- Temperature - 100°, Time - 2 minutes

PL05 -

LO°F

- 120°

PL06 -

LOCd

- Temperature - 100°, Time - 2 minutes

PL07 -

PPOF

- 150°

PL08 -

PPCd

- Temperature - 100°, Time - 3 minutes

PL09 -

LCdE

- Left coin denomination - 10¢

PL10 -

rCdE

- Right coin denomination - 25¢

PL11 -

tFAS

- Time for amount to start - 10 minutes

PL12 -

AtSt

- Amount To Start - 25¢

PL13 -

AFAt

- Amount for additional time - 10¢

PL14 -

Adrt

- Automatic dry maximum time - 30 minutes

PL15 -

GdLY

- Anti-wrinkle guard off delay time - 2 minutes

PL16 -

Gont

- Anti-wrinkle guard on time - 20-seconds

AGt

- Active anti-wrinkle guard time - 10 minutes

PL17 -

A and b

- “A” is adjustable from 1 to 99 (example: A = 5)

 

Factors

- “b” is adjustable from 1 to 99 (example: B = 75)

53

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferenceTable Of Contents Programming Instructions For all dryer models except AD-26/AD-295 and AD-540/WDA-540 Motor Circuit IndicatorFor dryer models AD-26/AD-295 Only Introduction Time for Amount to Start ANTI-WRINKLE Cool Down TemperaturesFree DRY Mode Cool Down TimeAutomatic Drytime Temperature DisplayDiagnostics Batterybackup OptionalFLS D. Displayand CodesClcc FillPush LCCPloc PPFOperating Instructions Timed ModeAutomatic Mode Patent no ,827,627 Free DRY Mode Program Selection Temperature Display ModeRight Coin Count rCC/LEFT Coin Count LCC Automatic Review of Program Location Automatic Mode AUtO Patent No ,827,627 PL01 Temperature Conversion StatusTimed Mode tInE ANTI-WRINKLE Program Grd Free DRY Mode FrEEBUZZ/TONE bUZ BAD Coin Lockout Status bCLO Coin Mode CoinBAD Coin Reset bCrS Flash Display Status FLSSingle Coin Accumulative Time AtInDual Coin PL10 rCdE PL11 tFAS PL12 AtSt Single Coin Acceptor Accumulative Coin ACOnDual Coinacceptor Rotational Safe Guard OPTIONALnSEn PL03 High Temperature HIFPL02 Percent DRY PdrY PL07 Permanent Press PPF PL05 LOW Temperature LOFPL13 Minimum Amount for Additional Time AFAt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL12 Amount to Start AtStPL16 Active Guard Time AGt PL15 ANTI-WRINKLE TimingPL17 a and b Factors Introduction to Programming Programming InstructionsProgramming Flowcharts Button Dryer Off Power On Display Reads No cycle in progressAnd/or ExampleProgramming Temperature Display ModeCycle In Progress Left Coin Count Right Coin Count Program Location 01 PL01 Press HI or LO keys and then Display will read anti-wrinkleGuard program status. If no change Press Perm Press key, otherwiseFLS AtIn LO Temp Continue HI Temp PL02 Perm Press Pdry Program Location 02 PL02Perm Press PL03 HIF Program Location 03 PL03Program Location 04 PL04 HI Temp cool down temperature/timeTime Decrease Time Increase Program Location 05 PL05 Program Location 06 PL06 LO Temp cool down temperature/timeTime Decrease PPF Program Location 07 PL07Program Location 08 PL08 Perm Press Cool Down Temperature/TimePL09 Perm Press LCdE Program Location 09 PL09Right Coin Denomination Program Location 10 PL10Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13Maximum Time for Auto Dry Program Location 14 PL14Anti-Wrinkle Timing Program Location 15 PL15Factor Increase Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Programmable 1 to Factor DecreaseFactory Preset PROGRAMS/PARAMETERS Single Coin only AFAt Amount for additional time 10¢ Dual Coin onlyLCdE Left coin denomination 10¢ TFAS Time for amount to start 10 minutesNSEn Rotational sensor not selected PdrY Percent Dry 98% HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes PPCd Temperature 80, Time 3 minutesPL08 PPCd Temperature 80, Time 3 minutes PL06 LOCd Temperature 80, Time 2 minutesRCdE Right coin denomination 10¢ Diagnostic L.E.D. Failure Codes Phase 5 Coin System DiagnosticsE.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08
Top Page Image Contents