Maytag W10151609A manual Complete Installation, If the dryer will not start, check the following

Page 13

7.Attach door hinges to dryer door so that the larger hole is at the bottom of the hinge.

8.Remove door strike (E) from cabinet. Use a small, flat-blade screwdriver to gently remove 4 hinge hole plugs (F) on left side of cabinet. Insert plugs into hinge holes on right side of cabinet.

9.Insert screws into bottom holes on left side of cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges.

10.Remove door strike plug (B). Insert the door strike you removed in Step 8 into hole and secure with screw. Insert door strike plug into original door strike hole and secure with screw.

11.Close door and check that door strike aligns with door catch (C). If it is needed, slide door catch left or right within slot to adjust alignment.

Complete Installation

1.Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2.Check that you have all of your tools.

3.Check the dryer’s final location. Be sure the vent is not crushed or kinked.

4.Check that the dryer is level. See “Level Dryer.”

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

5.Plug into a grounded 3 prong outlet. Turn on power.

6.Remove any protective film on the console and any tape remaining on the dryer.

7.Dispose of/recycle all packaging materials.

8.Read “Dryer Use.”

9.Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10.Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only Temperature setting.

If the dryer will not start, check the following:

Dryer is plugged into a grounded 3 prong outlet.

Electrical supply is connected.

Household fuse is intact and tight, or circuit breaker has not tripped.

Dryer door is closed.

11.When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and check that the gas supply line shutoff valve is open.

If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as outlined above.

If the gas supply line shutoff valve is open, contact a qualified technician.

13

Image 13
Contents W10151609A Sécheuse À GAZTable DES Matières Table of ContentsYour safety and the safety of others are very important Dryer SafetyImportant Safety Instructions Tools and Parts Installation InstructionsLocation Requirements Mobile Home Additional Installation Requirements Dryer DimensionsMobile home installations require Gas Supply Requirements Electrical RequirementsGas Type Gas Supply LineVenting Requirements Gas supply pressure testingGas supply connection requirements Burner Input RequirementsIf this is a new vent system Vent material If using an existing vent systemPlan Vent System Special provisions for mobile home installationsDetermine vent path Install Leveling Legs Install Vent SystemVent system chart Make Gas ConnectionConnect Vent Level DryerReverse Door Swing Optional If the dryer will not start, check the following Complete InstallationStarting Your Dryer Dryer USECleaning the Lint Screen Cleaning the Dryer LocationEvery Load Cleaning Drying Rack OptionRemoving Accumulated Lint Cleaning the Dryer InteriorVacation and Moving Care Changing the Drum LightDryer Operation TroubleshootingDryer Results Lint on load Cycle time too shortStains on load or drum Loads are wrinkledAccessories Assistance or ServiceU.S.A CanadaONE Year Limited Warranty Maytag Corporation Major Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA SécheuseImportantes Instructions DE Sécurité Exigences d’installation Instructions D’INSTALLATIONOutillage et pièces nécessaires Dimensions de la sécheuse Espacements d’installation’installation dans une maison mobile exige Type de gaz Spécifications électriquesGaz naturel Canalisation d’arrivée de gaz de la sécheuse Caractéristiques d’alimentation du brûleurAltitudes supérieures à 10 000 pi 3048 m Épreuve sous pression de l’alimentation en gazEn cas dutilisation du système dévacuation existant Exigences concernant lévacuationÉvacuation Planification du système d’évacuationDéterminer litinéraire dacheminement du conduit Autres installations où le dégagement est réduitInstallation des pieds de nivellement Installation du système d’évacuationRaccordement au gaz Pour utilisation dans une maison mobileMise à niveau de la sécheuse Raccordement du conduit d’évacuationSi la sécheuse ne démarre pas, vérifier ce qui suit Achever l’installationMise en marche de la sécheuse Utilisation DE LA SécheuseEntretien DE LA Sécheuse Nettoyage de lemplacement de la sécheuseOption grille de séchage Nettoyage de l’intérieur de la sécheuse Nettoyage du filtre à charpieComment enlever la charpie accumulée DéménagementChangement de l’ampoule du tambour DépannageFonctionnement de la sécheuse La minuterie ne progresse pas visiblement Résultats de la sécheuseTemps de programme trop court Accessoires Assistance OU ServiceAu Canada Garantie DES Gros Appareils Ménagers Maytag Corporation Tous droits réservés W10151609A SP PN W10151610A