Polaris 2003 MSX owner manual Jet Pump Intake, Ride Plate Impeller Drive Shaft

Page 45

Pre-Operation Inspection

Jet Pump Intake

1.	Ride Plate	2.	Impeller
3.	Drive Shaft	4.	Intake Grate

1	4

2

3

WARNING

Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When disconnecting cables, always disconnect the negative (black) cable first. When reconnecting, always connect the negative (black) cable last.

OPERATION

1.Remove the lanyard lock plate from the stop switch and disconnect the battery cables before inspecting the jet pump intake. Disconnect the negative (black) cable first.

2.Carefully check the jet pump intake and remove any weeds, shells or other debris that may restrict the intake of water.

3.After launching, walk the watercraft into water at least two feet (60 cm) deep and bounce the back of the craft up and down several times to flush out any sand and debris that may be in the pump.

CAUTION

A clogged intake or the ingestion of sand into the cooling system will cause engine overheating and result in jet pump or engine damage. If any obstruction cannot be removed, have an authorized Polaris dealer service it immediately. Clear the pump of sand after operating in shallow water or after beaching the watercraft.

43

Image 45

Contents MSX Page We’ve created a web site, just for YOU Page Welcome Polaris Recreational VehiclesPolaris Professional Series Workmobilest Table of Contents Do Your Part Your ResponsibilitiesAge Restrictions Maintenance RequirementsIdentification Numbers Signal Words and Symbols SafetySafety Decals Safety To Avoid Collisions Righting Capsized Boat Located on the engine water manifold Informational DecalsOperator Guidelines Operator SafetySafety Personal Floatation Device Safe Riding GearEye Protection Suit/Shoes/GlovesOverloading the Watercraft Fire SafetyProtective Apparel Weather and DarknessObstacles and Shallow Water Service and Maintenance Turning and AcceleratingPre-Operation Check Electrical Shock Hazard Jet Pump Water Intake SafetySafe Riding Position Lifting the WatercraftOperator Awareness Operator FitnessBoating Under the Influence Operator Fatigue and Dehydration Vehicle ModificationsHypothermia To avoid hypothermiaExhaust Outlet Reverse Gate Features and Controls911 Reverse Operation Handle Features and Controls Engine Components under seat Engine Components Accessible Functions New Generation Instrument NGIPrimary Functions Function Overview Instrument Operation Display ModeCheck Engine Display WarningsRPM Limiter Accessories Standard EquipmentOptional Equipment Emissions EPA Emissions RegulationsCalifornia Star Labels One Star Low Emission Two Stars Very Low EmissionThree Stars Ultra Low Emission Pre-Operation Inspection OperationWhat To Do Fuel Refueling Oil Ride Plate Impeller Drive Shaft Jet Pump IntakeSteering ThrottleEngine and Storage Compartments Loose Parts SeatFire Extinguisher Battery Hull Drain Plugs and BilgeRiding Gear Switches/Buttons Principles of Operation Engine Break-in ProcedureOperation Right-of-way and Give-way Navigational RulesStand-on Vessel Give-way VesselRule Encountering VesselsMeeting Vessels Crossing Paths Overtaking VesselsFishing Vessel Right-of-Way Non-Motorized CraftAvoid Collisions Reading Buoys and MarkersLaunch Ramp Etiquette Stopping the Engine Launching the WatercraftStarting the Engine Before Starting the EngineIf the Engine Doesn’t Start Boarding and Starting in Deep Water Operator Only Boarding the WatercraftBoarding With a Passenger Turning the Watercraft Reverse OperationStopping the Watercraft Beaching the Watercraft Operating in Rough Conditions Towing a Disabled Watercraft Righting a Capsized Watercraft Operating With Passengers Daily Care Post Operation MaintenanceOperation Temporary Storage Transporting The Watercraft Submerged Waterlogged Engine Anti-Corrosion TreatmentEngine Water Removal Procedure General Maintenance Maintenance and LubricationMaintenance Schedule Key Periodic Maintenance ScheduleDescription Fuel System Hull / Deck / Steering / Controls Lubrication Steering Cable Joints and Inner WireThrottle Cable Drive LineThrottle Body And Oil Injection Pump Seat Latch And Hooks Steering Nozzle Pivot ShaftElectrical Connections Steering Handle Pivot ShaftSpark Plugs Maintenance and Lubrication Hull and Deck Care Polaris VES II Synthetic Lubricant OilPolaris Premium Gold Synthetic Lubricant Polaris Nature Oil Synthetic LubricantSteering Cable Inspection FusesThrottle Cable Inspection Battery Maintenance and Charging BatteryReplenishing Battery Fluid AntidoteBattery Removal Battery Charging Battery Storage Battery InstallationJet Pump Water Inlet Screen Salt Water and Unclean Water CareCooling System Flushing Engine and Exhaust System Draining Extended StorageWatercraft Engine Fogging Procedure Cleaning Lubrication Engine Troubleshooting Engine Doesn’t Turn OverEngine Turns Over But Doesn’t Start Engine Runs Irregularly, Stalls or Misfires Possible Weak Spark Cause SolutionEngine Backfires Engine OverheatsEngine Pings or Knocks Engine Loses PowerUnusual Noise or Vibration From Propulsion System Engine RPM is Too High With Limited SpeedOil and Lubricants Polaris ProductsCapacities / Dimensions SpecificationsPropulsion Obtaining Service and Warranty Assistance WarrantyWarranty Policy Engine Oil HOW to Obtain Warranty ServicePolaris Watercraft Engines California Emission Control System Limited WarrantyOWNER’S Warranty Responsibilities 109 Emissions Index111