Polaris 2003 MSX owner manual Switches/Buttons

Page 50

OPERATION

Pre-Operation Inspection

Switches/Buttons

Perform these checks while the watercraft is in the water:

1.Check the inside of the engine compartment for fuel or water leaks. Do not operate the watercraft until any leaks have been repaired and the engine compartment has been ventilated.

2.Start the engine and let it run for a few seconds. Remove

the lanyard lock

2

plate (1) from

the engine stop

switch (2) to test

1

 

operation. The

 

engine should stop

 

immediately. If it

doesn’t, press the stop switch to stop the engine. Do not ride the watercraft. See your Polaris dealer for service before operating the watercraft.

3.If removing the lanyard lock plate successfully stopped the engine in the previous step, start the engine again and allow it to run for a few seconds. Depress the engine stop button. If the engine doesn’t stop immediately, remove the lanyard lock plate to stop the engine. Do not ride the watercraft. See your Polaris dealer for service before operating the watercraft.

48

Image 50
Contents MSX Page We’ve created a web site, just for YOU Page Polaris Professional Series Workmobilest WelcomePolaris Recreational Vehicles Table of Contents Your Responsibilities Do Your PartMaintenance Requirements Age RestrictionsIdentification Numbers Safety Signal Words and SymbolsSafety Decals Safety To Avoid Collisions Righting Capsized Boat Informational Decals Located on the engine water manifoldOperator Safety Operator GuidelinesSafety Eye Protection Safe Riding GearPersonal Floatation Device Suit/Shoes/GlovesFire Safety Overloading the WatercraftWeather and Darkness Protective ApparelObstacles and Shallow Water Pre-Operation Check Service and MaintenanceTurning and Accelerating Safe Riding Position Jet Pump Water Intake SafetyElectrical Shock Hazard Lifting the WatercraftBoating Under the Influence Operator AwarenessOperator Fitness Hypothermia Vehicle ModificationsOperator Fatigue and Dehydration To avoid hypothermiaFeatures and Controls Exhaust Outlet Reverse Gate911 Reverse Operation Handle Features and Controls Engine Components under seat Engine Components Primary Functions Accessible FunctionsNew Generation Instrument NGI Function Overview Display Mode Instrument OperationDisplay Warnings Check EngineRPM Limiter Optional Equipment AccessoriesStandard Equipment California Star Labels EmissionsEPA Emissions Regulations Three Stars Ultra Low Emission One Star Low EmissionTwo Stars Very Low Emission Operation Pre-Operation InspectionWhat To Do Fuel Refueling Oil Jet Pump Intake Ride Plate Impeller Drive ShaftEngine and Storage Compartments SteeringThrottle Fire Extinguisher Loose PartsSeat Battery Riding Gear HullDrain Plugs and Bilge Switches/Buttons Engine Break-in Procedure Principles of OperationOperation Stand-on Vessel Navigational RulesRight-of-way and Give-way Give-way VesselMeeting Vessels RuleEncountering Vessels Overtaking Vessels Crossing PathsNon-Motorized Craft Fishing Vessel Right-of-WayLaunch Ramp Etiquette Avoid CollisionsReading Buoys and Markers Launching the Watercraft Stopping the EngineBefore Starting the Engine Starting the EngineIf the Engine Doesn’t Start Boarding the Watercraft Boarding and Starting in Deep Water Operator OnlyBoarding With a Passenger Reverse Operation Turning the WatercraftStopping the Watercraft Beaching the Watercraft Operating in Rough Conditions Towing a Disabled Watercraft Righting a Capsized Watercraft Operating With Passengers Post Operation Maintenance Daily CareOperation Temporary Storage Transporting The Watercraft Anti-Corrosion Treatment Submerged Waterlogged EngineEngine Water Removal Procedure Maintenance and Lubrication General MaintenancePeriodic Maintenance Schedule Maintenance Schedule KeyDescription Fuel System Hull / Deck / Steering / Controls Throttle Cable Steering Cable Joints and Inner WireLubrication Drive LineElectrical Connections Seat Latch And Hooks Steering Nozzle Pivot ShaftThrottle Body And Oil Injection Pump Steering Handle Pivot ShaftSpark Plugs Maintenance and Lubrication Hull and Deck Care Polaris Premium Gold Synthetic Lubricant OilPolaris VES II Synthetic Lubricant Polaris Nature Oil Synthetic LubricantThrottle Cable Inspection Steering Cable InspectionFuses Replenishing Battery Fluid BatteryBattery Maintenance and Charging AntidoteBattery Removal Battery Charging Battery Installation Battery StorageSalt Water and Unclean Water Care Jet Pump Water Inlet ScreenCooling System Flushing Extended Storage Engine and Exhaust System DrainingWatercraft Engine Fogging Procedure Cleaning Lubrication Engine Turns Over But Doesn’t Start Engine TroubleshootingEngine Doesn’t Turn Over Possible Weak Spark Cause Solution Engine Runs Irregularly, Stalls or MisfiresEngine Overheats Engine BackfiresEngine Loses Power Engine Pings or KnocksEngine RPM is Too High With Limited Speed Unusual Noise or Vibration From Propulsion SystemPolaris Products Oil and LubricantsSpecifications Capacities / DimensionsPropulsion Warranty Obtaining Service and Warranty AssistanceWarranty Policy HOW to Obtain Warranty Service Engine OilCalifornia Emission Control System Limited Warranty Polaris Watercraft EnginesOWNER’S Warranty Responsibilities 109 Index Emissions111