Polaris 2003 MSX owner manual Battery Installation, Battery Storage

Page 91

MAINTENANCE AND LUBRICATION

Battery

Battery Installation

1. Set the battery in the
battery holder.	1

2.Install the battery vent tube. NOTE: It must be free of obstructions and

securely installed. If

not, battery gases Black (-) Red (+) could accumulate and

cause an explosion. The tube should be routed away from the frame and body to prevent corrosion. Avoid skin contact with electrolyte, which can cause severe burns.

3.Connect and tighten the red (positive) cable first.

4.Connect and tighten the black (negative) cable last.

5.Apply dielectric grease to each cable.

6.Reinstall the battery cover and attach the hold-down straps.

7.Verify that cables are properly routed.

NOTE: When installing a new battery, make sure it’s fully charged prior to its initial use. Using a new battery that has not been fully charged can damage the battery and result in a shorter life. It can also hinder vehicle performance.

Battery Storage

1.Remove the battery. Clean the casing and terminals with baking soda and water (one tablespoon of baking soda to one cup water). Apply dielectric grease or petroleum jelly to battery terminals and all exposed cable connectors.

2.Top off the battery with distilled water and charge it to a specific gravity of 1.26.

3.Recharge the battery monthly to prevent battery discharge and sulfating or use a Polaris Battery Tendert battery charger or similar trickle charger to maintain the charge during the storage period. Follow the instructions provided with the charger.

4.Store the battery in a cool, dry place out of direct sunlight.

89

Image 91

Contents MSX Page We’ve created a web site, just for YOU Page Polaris Recreational Vehicles WelcomePolaris Professional Series Workmobilest Table of Contents Do Your Part Your ResponsibilitiesAge Restrictions Maintenance RequirementsIdentification Numbers Signal Words and Symbols SafetySafety Decals Safety To Avoid Collisions Righting Capsized Boat Located on the engine water manifold Informational DecalsOperator Guidelines Operator SafetySafety Suit/Shoes/Gloves Safe Riding GearPersonal Floatation Device Eye ProtectionOverloading the Watercraft Fire SafetyProtective Apparel Weather and DarknessObstacles and Shallow Water Turning and Accelerating Service and MaintenancePre-Operation Check Lifting the Watercraft Jet Pump Water Intake SafetyElectrical Shock Hazard Safe Riding PositionOperator Fitness Operator AwarenessBoating Under the Influence To avoid hypothermia Vehicle ModificationsOperator Fatigue and Dehydration HypothermiaExhaust Outlet Reverse Gate Features and Controls911 Reverse Operation Handle Features and Controls Engine Components under seat Engine Components New Generation Instrument NGI Accessible FunctionsPrimary Functions Function Overview Instrument Operation Display ModeCheck Engine Display WarningsRPM Limiter Standard Equipment AccessoriesOptional Equipment EPA Emissions Regulations EmissionsCalifornia Star Labels Two Stars Very Low Emission One Star Low EmissionThree Stars Ultra Low Emission Pre-Operation Inspection OperationWhat To Do Fuel Refueling Oil Ride Plate Impeller Drive Shaft Jet Pump IntakeThrottle SteeringEngine and Storage Compartments Seat Loose PartsFire Extinguisher Battery Drain Plugs and Bilge HullRiding Gear Switches/Buttons Principles of Operation Engine Break-in ProcedureOperation Give-way Vessel Navigational RulesRight-of-way and Give-way Stand-on VesselEncountering Vessels RuleMeeting Vessels Crossing Paths Overtaking VesselsFishing Vessel Right-of-Way Non-Motorized CraftReading Buoys and Markers Avoid CollisionsLaunch Ramp Etiquette Stopping the Engine Launching the WatercraftStarting the Engine Before Starting the EngineIf the Engine Doesn’t Start Boarding and Starting in Deep Water Operator Only Boarding the WatercraftBoarding With a Passenger Turning the Watercraft Reverse OperationStopping the Watercraft Beaching the Watercraft Operating in Rough Conditions Towing a Disabled Watercraft Righting a Capsized Watercraft Operating With Passengers Daily Care Post Operation MaintenanceOperation Temporary Storage Transporting The Watercraft Submerged Waterlogged Engine Anti-Corrosion TreatmentEngine Water Removal Procedure General Maintenance Maintenance and LubricationMaintenance Schedule Key Periodic Maintenance ScheduleDescription Fuel System Hull / Deck / Steering / Controls Drive Line Steering Cable Joints and Inner WireLubrication Throttle CableSteering Handle Pivot Shaft Seat Latch And Hooks Steering Nozzle Pivot ShaftThrottle Body And Oil Injection Pump Electrical ConnectionsSpark Plugs Maintenance and Lubrication Hull and Deck Care Polaris Nature Oil Synthetic Lubricant OilPolaris VES II Synthetic Lubricant Polaris Premium Gold Synthetic LubricantFuses Steering Cable InspectionThrottle Cable Inspection Antidote BatteryBattery Maintenance and Charging Replenishing Battery FluidBattery Removal Battery Charging Battery Storage Battery InstallationJet Pump Water Inlet Screen Salt Water and Unclean Water CareCooling System Flushing Engine and Exhaust System Draining Extended StorageWatercraft Engine Fogging Procedure Cleaning Lubrication Engine Doesn’t Turn Over Engine TroubleshootingEngine Turns Over But Doesn’t Start Engine Runs Irregularly, Stalls or Misfires Possible Weak Spark Cause SolutionEngine Backfires Engine OverheatsEngine Pings or Knocks Engine Loses PowerUnusual Noise or Vibration From Propulsion System Engine RPM is Too High With Limited SpeedOil and Lubricants Polaris ProductsCapacities / Dimensions SpecificationsPropulsion Obtaining Service and Warranty Assistance WarrantyWarranty Policy Engine Oil HOW to Obtain Warranty ServicePolaris Watercraft Engines California Emission Control System Limited WarrantyOWNER’S Warranty Responsibilities 109 Emissions Index111