Polaris 2003 MSX owner manual Engine Water Removal Procedure

Page 75

Post Operation Maintenance

Engine Water Removal Procedure

Use the following procedure for removing water from a submerged engine. Attempt this procedure only if you are mechanically experienced and have adequate assistance for lifting and supporting the watercraft.

WARNING

Accidental starting during the water removal procedure could cause severe personal injury. Before removing water from a submerged engine, make sure the lanyard cord and lock plate are removed from the engine stop switch.

1.Remove the watercraft from the water. Remove the lanyard cord from the engine stop switch and place the watercraft on a flat surface, allowing room to roll it onto its side later.

2.Remove the drain plugs and drain the water from the bilge.

OPERATION

3.Remove the seat and remove the spark plugs.

4.Tip the watercraft on its right side (to starboard) until the spark plug holes are just below horizontal. While assistants hold the watercraft in this position, turn the driveshaft by hand to rotate the engine and allow the water to run out.

5.Upright the watercraft and inspect and dry the spark plug holes. Install new spark plugs.

6.Install the air intake.

7.Check the battery vent hose for obstructions and drain any water from the hose.

8.Check the fuel and oil for the presence of water. If water is present, take the watercraft to an authorized Polaris dealer for immediate service. Do not run the craft if water is present in the fuel or oil.

9.Verify that no air is present in the oil line.

10.Reinstall the drain plugs and the seat.

73

Image 75

Contents MSX Page We’ve created a web site, just for YOU Page Welcome Polaris Recreational VehiclesPolaris Professional Series Workmobilest Table of Contents Do Your Part Your ResponsibilitiesAge Restrictions Maintenance RequirementsIdentification Numbers Signal Words and Symbols SafetySafety Decals Safety To Avoid Collisions Righting Capsized Boat Located on the engine water manifold Informational DecalsOperator Guidelines Operator SafetySafety Suit/Shoes/Gloves Safe Riding GearPersonal Floatation Device Eye ProtectionOverloading the Watercraft Fire SafetyProtective Apparel Weather and DarknessObstacles and Shallow Water Service and Maintenance Turning and AcceleratingPre-Operation Check Lifting the Watercraft Jet Pump Water Intake SafetyElectrical Shock Hazard Safe Riding PositionOperator Awareness Operator FitnessBoating Under the Influence To avoid hypothermia Vehicle ModificationsOperator Fatigue and Dehydration HypothermiaExhaust Outlet Reverse Gate Features and Controls911 Reverse Operation Handle Features and Controls Engine Components under seat Engine Components Accessible Functions New Generation Instrument NGIPrimary Functions Function Overview Instrument Operation Display ModeCheck Engine Display WarningsRPM Limiter Accessories Standard EquipmentOptional Equipment Emissions EPA Emissions RegulationsCalifornia Star Labels One Star Low Emission Two Stars Very Low EmissionThree Stars Ultra Low Emission Pre-Operation Inspection OperationWhat To Do Fuel Refueling Oil Ride Plate Impeller Drive Shaft Jet Pump IntakeSteering ThrottleEngine and Storage Compartments Loose Parts SeatFire Extinguisher Battery Hull Drain Plugs and BilgeRiding Gear Switches/Buttons Principles of Operation Engine Break-in ProcedureOperation Give-way Vessel Navigational RulesRight-of-way and Give-way Stand-on VesselRule Encountering VesselsMeeting Vessels Crossing Paths Overtaking VesselsFishing Vessel Right-of-Way Non-Motorized CraftAvoid Collisions Reading Buoys and MarkersLaunch Ramp Etiquette Stopping the Engine Launching the WatercraftStarting the Engine Before Starting the EngineIf the Engine Doesn’t Start Boarding and Starting in Deep Water Operator Only Boarding the WatercraftBoarding With a Passenger Turning the Watercraft Reverse OperationStopping the Watercraft Beaching the Watercraft Operating in Rough Conditions Towing a Disabled Watercraft Righting a Capsized Watercraft Operating With Passengers Daily Care Post Operation MaintenanceOperation Temporary Storage Transporting The Watercraft Submerged Waterlogged Engine Anti-Corrosion TreatmentEngine Water Removal Procedure General Maintenance Maintenance and LubricationMaintenance Schedule Key Periodic Maintenance ScheduleDescription Fuel System Hull / Deck / Steering / Controls Drive Line Steering Cable Joints and Inner WireLubrication Throttle CableSteering Handle Pivot Shaft Seat Latch And Hooks Steering Nozzle Pivot ShaftThrottle Body And Oil Injection Pump Electrical ConnectionsSpark Plugs Maintenance and Lubrication Hull and Deck Care Polaris Nature Oil Synthetic Lubricant OilPolaris VES II Synthetic Lubricant Polaris Premium Gold Synthetic LubricantSteering Cable Inspection FusesThrottle Cable Inspection Antidote BatteryBattery Maintenance and Charging Replenishing Battery FluidBattery Removal Battery Charging Battery Storage Battery InstallationJet Pump Water Inlet Screen Salt Water and Unclean Water CareCooling System Flushing Engine and Exhaust System Draining Extended StorageWatercraft Engine Fogging Procedure Cleaning Lubrication Engine Troubleshooting Engine Doesn’t Turn OverEngine Turns Over But Doesn’t Start Engine Runs Irregularly, Stalls or Misfires Possible Weak Spark Cause SolutionEngine Backfires Engine OverheatsEngine Pings or Knocks Engine Loses PowerUnusual Noise or Vibration From Propulsion System Engine RPM is Too High With Limited SpeedOil and Lubricants Polaris ProductsCapacities / Dimensions SpecificationsPropulsion Obtaining Service and Warranty Assistance WarrantyWarranty Policy Engine Oil HOW to Obtain Warranty ServicePolaris Watercraft Engines California Emission Control System Limited WarrantyOWNER’S Warranty Responsibilities 109 Emissions Index111