Teledyne 465L operation manual Specifications and Agency Approvals

Page 17

2.SPECIFICATIONS AND AGENCY APPROVALS

2.1.Specifications

 

User selectable to any full scale range from:

Ranges

1 PPM to 500 PPM

1000 PPB to 10,000 PPB

 

 

2000 µg/m3 to 10,000 µg/m3

 

100 PPHM to 10,000 PPHM (optional

 

configuration)

 

PPM, PPB, µg/m3, PPHM (optional

Measurement Units

configuration)

Zero Noise

< .0015 PPM (rms)

Span Noise

< .5% of reading (rms) (above 0.1 PPM)

Lower Detectable Limit

< .003 PPM (rms)

Accuracy

+/- 1% of full scale range

 

<30 sec

Response Time (95%)

(<60 sec with the Sample Conditioner option)

Sample Flow Rate

0.8 L/min

Temperature Range

5-45oC

Humidity Range

10-90% RH, Non-Condensing

 

5.22” x 19.0" x 15.3" (133 mm x 483 mm x 388

Dimensions (H x W x D)

mm) – Rack Mount Version

16.01” x 15.6” x 6.90” (407mm x 396mm x

 

 

175mm) – with NEMA 4X enclosure

Weight

12.6 lb. (5.73 kg) - Rack Mount Version

 

15.2 lb. (6.91 kg) – with NEMA 4X enclosure

Power

100-240 VAC, 47-63 Hz, 74W max

Environmental Conditions

Installation Category (Overvoltage Category) II

 

Pollution Degree 2

Maximum Operating Altitude

2000 meters

05509F DCN6409

15

Image 17
Contents Model 465L Ozone Monitor Page About Teledyne Advanced Pollution Instrumentation Tapi This page intentionally left blank General Safety Hazard Important Safety InformationMise EN Garde Consignes DE SécuritéPart Name/Description Number About this ManualRevision History Table of Contents Digital Communications Figures Sensor Detail Tables Xii 05509F DCN6409 Preface IntroductionThis page intentionally left blank Specifications Specifications and Agency ApprovalsMulti-Stream Specifications SafetyApprovals EMCPhone Other Type CertificationsThis page intentionally left blank = − InHg × ln ×  273 Principle of Operation05509F DCN6409 Getting Started Nema AC Power Connection to Monitor Pneumatic Connections Pneumatic Connections, Rack Mount ConfigurationSample Gas Connection Pneumatic Connections, Nema Configuration, Multi-StreamSample System Design in Humid Environments Sample Filtration05509F DCN6409 Permeation Gas Dryer Option Sample Conditioner OptionRear Panel Electrical I/O Connections Exhaust ConnectionElectrical I/O Connections Location of I/O Connectors in the Nema ConfigurationAnalog Output Status OutputsStatus Name Normal Operating Output # State Status Output SchematicRelay # Function Normal Operating State Hi-Current Relay OutputsRelay # Function Normal Operating StateRelay # Function Meaning Multi-Stream Relay Outputs Optional6.1. RS232 Connection Digital Serial Interfaces6.2. RS485 Connection Ethernet ConnectionHis page intentionally left blank Frequently Asked Questions This page intentionally left blank Options 05509F DCN6409 Front Panel Overview OperationOzone Concentration Display Menu Navigation KeypadStream Selector Status/Control Optional Concentration Alarm Status/ResetAlarm Status LED Color Alarm State Front Panel Menus Status LEDsMenu Navigation Basics Status LED Normal StateEditing Numeric Values Front Panel Menu Diagram OFF Point 5V Output MA Output Diag MenuAnalog Step-Test Signal Name Rear Panel Label Function Signal I/OZero Calibration Memory ResetSpan Calibration Span Cal Menu Flow Calibration Optional Electronic Flowmeter onlyFlow Cal Menu View Menu Config MenuParameter Meaning UnitsCount SETUP-VARS MenuProperty Meaning Default Range Value SETUP-STREAM MenuMulti-Stream Operation Digital Communications Overview Changing Com Port Hardware ConfigurationDigital Communications RS232 Configuration Property Value RS-232 ConfigurationFunction DB-9 General I/O Connector Pin SW2 DTE SW2 DCE Function DB-9 General I/O Connector Pin SW2 DCE RS-485 ConfigurationHardware Setup for Configuring the Ethernet Module Ethernet ConfigurationVerifying Network Hardware Connection Link LED Left Side Activity LED Right Side Color MeaningManually Assigning a Static IP Address Determining a Dynamically Assigned IP Address Dhcp ModeModbus Register Maps Modbus Commands SupportedDescription Function CodeDecimal Address Description Register Type Start Bit # Bits Real-Time Concentration and Status Registers Read OnlyInstrument Setup and Configuration Registers Read / Write Decimal Address Description Register Type Start Bit # Bits This page intentionally left blank Maintenance Item Recommended Interval Section Maintenance and AdjustmentsMaintenance Schedule Instrument Layout Instrument Layout, Rack Mount ConfigurationReplacing Internal Particulate Filter Instrument Layout, Nema ConfigurationUV Lamp Adjustment Sample Pump Replacement UV Lamp Replacement05509F DCN6409 Sensor Detail Sensor Valve ReplacementConfiguring the Analog Output Water Drop-Out Filter Option MaintenanceBoot Loader Operation Cleaning Exterior Surfaces of the M465LUpload Firmware Boot Loader Hardware SetupBoot Loader Software Setup Verify Firmware This page intentionally left blank Reference Drawings TroubleshootingPneumatic Diagram RACK-MOUNT Version only Interconnect DiagramStatus LED/Output Definitions Sensor OK Pneumatic ErrorInvalid Reading Check LampPressure Too Low Pressure Too HighThis page intentionally left blank Zero Calibration CalibrationFactory Calibration This page intentionally left blank Spare Parts 12.1. M465L Rack Mount Spare Parts ListPart Number Description 12.2. M465L Nema Spare Parts ListCONNECTOR, 16 PIN, W/SCREW Flange This page intentionally left blank Permeation Gas Dryer Index