Schneider Electric EM4000 manual Installing 5A Converters and CTs on the PowerLogic EM4080

Page 29

930-134-01-A.00

PowerLogicTM Series EM4000

11/2013

Installation Guide

 

 

 

 

 

 

 

 

 

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Turn off all power supplying this equipment before working on or inside the equipment.

Always use a properly rated voltage sensing device to confirm the power is off.

NEVER open circuit a CT; use the shorting block to short circuit the leads of the CT before removing the connection from the meter.

Do not crimp the insulation when making the wire connections.

Failure to follow these instructions will result in death or serious injury.

1.Connect the 50-pin connector to the PowerLogic connector located at the bottom side of the unit, and secure it in place with the retaining clips.

2.Feed the free end of the cable through the bottom left of the meter enclosure.

This cable is made up of twisted-pair wires for connecting the individual CTs to the metered points. The color codes for the X1 (positive) and X2 (neutral) connections for each CT are listed in Table 2 on page 24.

NOTE: The direction of the energy flow is indicated on the CT.

3.Turn off the power feed to the panel where the CTs are being installed. Always use a properly rated voltage sensing device to confirm power is off.Feed the CT cable into the panel through an appropriate punch-out with an approved strain relief.

4.Strip the plastic sheaths on the cable to an appropriate length to expose the wire pairs. Cut and strip the CT leads and wire pair leads to an appropriate length. Crimp the CT leads to the wire pairs for each meter point.

5.Connect the X1 lead of the CT to the X1 lead of the cable, then connect the X2 lead of the CT to the X2 lead of the cable (see Table 2).

6.When using solid-core CTs, remove the feed wire from the circuit breaker, place the CT over the wire, and reconnect to the circuit breaker. Ensure that the arrow on the CT label is pointing in the direction of the energy flow (toward the load).

7.When using split-core CTs, separate the halves of the CT and place the CT over the wire to the circuit breaker. Ensure that the CT is facing the source as shown on the label. Install cable ties to ensure that the CT halves are held together securely.

8.Repeat steps 4 to 7 for the remaining CTs.

Installing 5A Converters and CTs on the PowerLogic EM4080

When both low-current (200A and 400A) and high-current (600A or higher) circuits need to be measured with the same PowerLogic meter, converters are available to allow the use of Measurement Canada approved 5A CTs with the appropriate current rating. 5A CT converters transform the 5A maximum output from a standard CT to the 80mA maximum of the PowerLogic meter.

The 5A side of the converter is the black and red wire pair, and the 80mA side of the converter is the black and white wire pair.

NOTE: It is recommended that 5A converters and shorting devices be installed in a sealable metal enclosure.

©2013 Schneider Electric All Rights Reserved

21

Image 29
Contents PowerLogicTM Series EM4000 Page Please note Important InformationFCC Part 68 Notice FCC Part 15 NoticeNetwork Compatibility Notice for the Internal Modem Page Table of Contents Schneider Electric All Rights Reserved System Description PowerLogic EM4000 series System SpecificationsIntroduction PowerLogic EM4000 series meter specifications Front Panel Display PowerLogic EM4080 front panelPowerLogic EM4033 and PowerLogic EM4080 internal view Electrical Standards Compliance Safety PrecautionsPre-Installation InstallationPre-Installation Checklist ReceivingMounting the PowerLogic EM4000 meter Installation ProceduresAccess to Power and Lighting 11.0 27.9 cm EM4033 11/2013 Installation Guide Shorting block detail 930-134-01-A.00 Hazard of Electric SHOCK, EXPLOSION, or ARC Flash For a single-phase panel with the 120V variant of the meter Schneider Electric All Rights Reserved From Panel Schneider Electric All Rights Reserved PowerLogic EM4000 meter three-phase Delta service connection Delta service meteringInstalling the Current Transformers PowerLogic EM4033 split-core 0.333V current transformer Source Installing 5A Converters and CTs on the PowerLogic EM4080 Shows a 5A CT connected to the converter StepsPowerLogic EM4080 5A CT connection to converter PowerLogic EM4000 meter CT color pair identification Connecting the Modbus RTU Communications Connecting the CommunicationsConnecting the Ethernet Cable Start-Up Sequence Connecting Pulse InputsManually Testing Communications Display Navigation Normal ModeDiagnostics Mode Recording the Meter Map Installation Record sample shown Fuse Replacement MaintenanceRegulatory Compliance Equipment servicing and accessGraphical symbols that appear on equipment Numerics IndexPowerLogicTM EM4000 Series 930-134-01-A.00 Index 11/2013 Page Schneider Electric