Dell E02B owner manual

Page 111

Expanded operating temperature

 

For temperatures between 40°C and 45°C, de-

 

rate maximum allowable temperature by 1°C per

 

125 m above 950 m (1°F per 228 ft).

Expanded operating temperature restrictions

• Do not perform a cold startup below 5 °C.

 

• Maximum 105 W processor is supported.

 

• The following do not support the expanded

 

operating temperature range:

 

– PCIe SSDs

 

– Non Dell-qualified peripheral cards and/or

 

peripheral cards greater than 25 W

 

• When populating the sled slots in the FX2s

 

enclosure with only PowerEdge FC630 sleds:

 

– Install 104 mm width heat sink for

 

processors of less than 105 W.

 

– If you install a sled with two processors in

 

the FX2s enclosure, all sled slots in the

 

enclosure must have PowerEdge FC630

 

sleds with the same configuration.

 

However, vacant sled slots in the enclosure

 

can be installed with sled blanks.

111

Image 111
Contents Dell PowerEdge FC630 Page Contents Installing and removing sled components Troubleshooting your system Using System Diagnostics 102 Jumpers and connectors 104Technical specifications 107 Getting help 112 About your system Front-panel features and indicatorsHard-drive/SSD indicator patterns Using USB diskette or USB DVD/CD drivesHard-drive/SSD indicators IDRAC Direct LED indicator codesIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up and configuring the iDRAC IP address Setting up your systemLogging in to iDRAC Installing the operating system Page Navigation keys About System SetupEntering System Setup System Setup Main MenuSystem Bios screen System Memory screen System Information screenATS Processor Settings screenSata Settings screen Post Page Network Settings screen Boot Settings screenIntegrated Devices screen Serial Communication screen C1E System Profile Settings screenSystem Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screenPage Boot Manager main menu About Boot ManagerAbout Dell Lifecycle Controller Changing the boot order Entering Boot ManagerAssigning a system and/or setup password Choosing the system boot modeUsing your system password to secure your system Operating with a setup password enabled IDRAC Settings utilityEmbedded systems management Entering the iDRAC Settings utility After working inside your system Safety instructionsRecommended tools Before working inside your systemRemoving the sled Removing and installing a sledO connector cover Removing and installing the sled Installing the sledNDC Inside the sledRemoving the cooling shroud Cooling shroudInstalling the cooling shroud Processor/DIMM blankRemoving a processor/DIMM blank Removing and installing a processor/DIMM blank Installing a processor/DIMM blankLrdimm System memoryProcessor General memory-module installation guidelines Advanced ECC Lockstep Mode-specific guidelinesSample memory configurations Memory configurations two processors Removing memory modules Removing the memory module Installing memory modulesRemoving a PCIe mezzanine card PCIe mezzanine cardRemoving and installing a PCIe mezzanine card Installing a PCIe mezzanine card Idsdm card optionalReplacing an SD card Ensure that you read the Safety instructions Replacing an SD card Internal USB keyReplacing the internal USB key Removing the Idsdm card Removing and installing the Idsdm cardInstalling the Idsdm card Removing the rSPI card RSPI card optionalInstalling the rSPI card SD vFlash cardReplacing the SD vFlash card Removing the Network Daughter Card Network Daughter CardInstall the NDC. See Installing the Network Daughter Card Processors Installing the Network Daughter CardRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing and removing a processor Installing a processorPage Applying thermal grease on the top of the processor Hard drive/SSD installation guidelines Hard drives/SSDsHard-drive/SSD bay numbering Removing a hard drive/SSD Removing and installing a hard drive/SSDRemoving a hard-drive/SSD blank Installing a hard drive/SSDHard-drive/SSD blank Release latch Installing a hard-drive/SSD blank Shutdown procedure for servicing a hard drive/SSDConfiguring the boot drive Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Removing the hard-drive/SSD cage Installing a 1.8 inch SSD in a 1.8 inch SSD carrierRemoving and installing a hard-drive/SSD cage Installing the hard-drive/SSD cageRemoving the hard-drive/SSD backplane Hard-drive backplaneRemoving and installing the hard-drive/SSD backplane Installing the hard-drive/SSD backplane Removing a Perc H730P slim card Perc H730P slim cardRemoving and installing a Perc H730P slim card Installing a Perc H730P slim cardRemoving the PCIe extender/storage controller card Storage controller cardPage Installing the PCIe extender/storage controller card Replacing the Nvram backup battery Nvram backup batteryReplacing the Nvram backup battery Removing the system board System boardPage Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Trusted Platform Module Installing the Trusted Platform ModuleRe-enabling the TPM for TXT users Re-enabling the TPM for BitLocker usersTroubleshooting your system Troubleshooting USB devices Troubleshooting hard drivesTroubleshooting Solid State Drives Troubleshooting processors Troubleshooting an internal SD cardTroubleshooting the Nvram backup battery Troubleshooting the system boardDiagnostic messages System messagesAlert messages Dell Embedded System Diagnostics When to use the Embedded System DiagnosticsRunning the Embedded System Diagnostics System diagnostics controls Running Embedded System Diagnostics from an external mediaSystem board jumper settings Jumpers and connectorsCPU1 System board connectorsDisabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Page Locating your system Service Tag Contacting DellDocumentation feedback 113