Dell E02B owner manual Troubleshooting an internal SD card, Troubleshooting processors

Page 99

Troubleshooting an internal SD card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Steps

1.Enter the System Setup and ensure that the Internal SD Card Port is enabled.

2.Note the Internal SD Card Redundancy option is enabled in the Integrated Devices screen of the System Setup (Mirror or Disabled).

3.Turn off the sled using the operating system commands or the CMC.

4.Remove the sled from the enclosure.

5.If the Internal SD Card Redundancy option in the Integrated Devices screen of the System Setup is set to Mirror mode and SD card 1 has failed:

a.Remove the SD card from SD card slot 1.

b.Remove the SD card present in SD card slot 2 and insert it into SD card slot 1.

c.Install a new SD card in slot 2.

6.If the Internal SD Card Redundancy option in the Integrated Devices screen of the System Setup is set to Mirror mode and SD card 2 has failed, insert the new SD card into SD card slot 2.

7.If the Internal SD Card Redundancy option in Integrated Devices screen of the System Setup is set to Disabled, replace the failed SD card with a new SD card.

8.Install the sled in the enclosure.

9.Turn on the sled.

10.Enter the System Setup and ensure that the Internal SD Card Port option is enabled and Internal SD Card Redundancy option is set to Mirror mode.

11.Check if the SD card is functioning properly. If the problem persists, see Getting Help.

Related Links

Removing the sled

Installing the sled

Removing a hard drive/SSD

Troubleshooting processors

1.Turn off the sled using the operating system commands or the CMC.

2.Remove the sled from the enclosure.

3.Ensure that the processor(s) and heat sink(s) are properly installed.

4.If your system only has one processor installed, ensure that it is installed in the primary processor socket (CPU1).

5.Install the sled in the enclosure.

6.Turn on the sled.

7.Run the appropriate diagnostic test. For more information, see Using System Diagnostics. If the problem persists, see Getting Help.

99

Image 99

Contents Dell PowerEdge FC630 Page Contents Installing and removing sled components Troubleshooting your system Using System Diagnostics 102 Jumpers and connectors 104Technical specifications 107 Getting help 112 About your system Front-panel features and indicatorsHard-drive/SSD indicator patterns Using USB diskette or USB DVD/CD drivesHard-drive/SSD indicators IDRAC Direct LED indicator codesIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up and configuring the iDRAC IP address Setting up your systemLogging in to iDRAC Installing the operating system Page Navigation keys About System SetupEntering System Setup System Setup Main MenuSystem Bios screen System Memory screen System Information screenATS Processor Settings screenSata Settings screen Post Page Network Settings screen Boot Settings screenIntegrated Devices screen Serial Communication screen C1E System Profile Settings screenSystem Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screenPage Boot Manager main menu About Boot ManagerAbout Dell Lifecycle Controller Changing the boot order Entering Boot ManagerAssigning a system and/or setup password Choosing the system boot modeUsing your system password to secure your system Operating with a setup password enabled IDRAC Settings utilityEmbedded systems management Entering the iDRAC Settings utility After working inside your system Safety instructionsRecommended tools Before working inside your systemRemoving the sled Removing and installing a sledO connector cover Removing and installing the sled Installing the sledNDC Inside the sledRemoving the cooling shroud Cooling shroudInstalling the cooling shroud Processor/DIMM blankRemoving a processor/DIMM blank Removing and installing a processor/DIMM blank Installing a processor/DIMM blankLrdimm System memoryProcessor General memory-module installation guidelines Advanced ECC Lockstep Mode-specific guidelinesSample memory configurations Memory configurations two processors Removing memory modules Removing the memory module Installing memory modulesRemoving a PCIe mezzanine card PCIe mezzanine cardRemoving and installing a PCIe mezzanine card Installing a PCIe mezzanine card Idsdm card optionalReplacing an SD card Ensure that you read the Safety instructions Replacing an SD card Internal USB keyReplacing the internal USB key Removing the Idsdm card Removing and installing the Idsdm cardInstalling the Idsdm card Removing the rSPI card RSPI card optionalInstalling the rSPI card SD vFlash cardReplacing the SD vFlash card Removing the Network Daughter Card Network Daughter CardInstall the NDC. See Installing the Network Daughter Card Processors Installing the Network Daughter CardRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing and removing a processor Installing a processorPage Applying thermal grease on the top of the processor Hard drive/SSD installation guidelines Hard drives/SSDsHard-drive/SSD bay numbering Removing a hard drive/SSD Removing and installing a hard drive/SSDRemoving a hard-drive/SSD blank Installing a hard drive/SSDHard-drive/SSD blank Release latch Installing a hard-drive/SSD blank Shutdown procedure for servicing a hard drive/SSDConfiguring the boot drive Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Removing the hard-drive/SSD cage Installing a 1.8 inch SSD in a 1.8 inch SSD carrierRemoving and installing a hard-drive/SSD cage Installing the hard-drive/SSD cageRemoving the hard-drive/SSD backplane Hard-drive backplaneRemoving and installing the hard-drive/SSD backplane Installing the hard-drive/SSD backplane Removing a Perc H730P slim card Perc H730P slim cardRemoving and installing a Perc H730P slim card Installing a Perc H730P slim cardRemoving the PCIe extender/storage controller card Storage controller cardPage Installing the PCIe extender/storage controller card Replacing the Nvram backup battery Nvram backup batteryReplacing the Nvram backup battery Removing the system board System boardPage Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Trusted Platform Module Installing the Trusted Platform ModuleRe-enabling the TPM for TXT users Re-enabling the TPM for BitLocker usersTroubleshooting your system Troubleshooting USB devices Troubleshooting hard drivesTroubleshooting Solid State Drives Troubleshooting processors Troubleshooting an internal SD cardTroubleshooting the Nvram backup battery Troubleshooting the system boardDiagnostic messages System messagesAlert messages Dell Embedded System Diagnostics When to use the Embedded System DiagnosticsRunning the Embedded System Diagnostics System diagnostics controls Running Embedded System Diagnostics from an external mediaSystem board jumper settings Jumpers and connectorsCPU1 System board connectorsDisabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Page Locating your system Service Tag Contacting DellDocumentation feedback 113