Dell E02B owner manual Integrated Devices screen

Page 24

Menu Item

Description

 

 

PXE Device n (n = 1 to 4)

Enables or disables the device. When enabled, a UEFI boot option is

 

created for the device.

PXE Device n Settings (n = 1 Allows you to control the configuration of the PXE device. to 4)

Integrated Devices screen

Integrated Devices screen allows you to view and configure the settings of all integrated devices including the video controller, integrated RAID controller, and the USB ports.

In the System Setup Main Menu, click System BIOS → Integrated Devices.

Menu Item

Description

 

 

USB 3.0 Setting

Allows you to enable or disable the USB 3.0 support Enable this option

 

only if your operating system support USB 3.0. Disabling this allows

 

devices to operate at USB 2.0 speed. USB 3.0 is disabled by default

User Accessible USB Ports

Allows you to enable or disable the USB ports. Selecting Only Back Ports

 

On disables the front USB ports, selecting All Ports Off disables all USB

 

ports. The USB keyboard and mouse operates during boot process in

 

certain operating systems. After the boot process is complete, the USB

 

keyboard and mouse does not work if the ports are disabled.

 

NOTE: Selecting Only Back Ports On and All Ports Off will disable

 

the USB management port and also restrict access to iDRAC

 

features.

Internal USB Port

Allows you to enable or disable the internal USB port.

Integrated RAID Controller

Allows you to enable or disable the integrated RAID controller.

 

NOTE: This feature is not supported for the PowerEdge T630

 

system.

Integrated Network Card 1

Allows you to enable or disable the integrated network card.

I/OAT DMA Engine

Allows you to enable or disable the I/OAT option Enable only if the

 

hardware and software supports the feature.

Embedded Video Controller Allows you to enable or disable the Embedded Video Controller. By default, the embedded video controller is Enabled. Current state of Embedded Video Controller is Enabled. Current State of Embedded Video Controller is a read only field, indicating the current state for the Embedded Video Controller. If the Embedded Video Controller is the only display capability in the system (that is, no add-in graphics card is installed), then the Embedded Video Controller is automatically used as the primary display even if the Embedded Video Controller setting is Disabled.

SR-IOV Global Enable

Allows you to enable or disable the BIOS configuration of Single Root I/O

 

Virtualization (SR-IOV) devices. By default, the SR-IOV Global Enable

 

option is set to Disabled.

OS Watchdog Timer

If your system stops responding, this watchdog timer aids in the recovery

 

of your operating system. When this field is set to Enabled, the operating

 

system is allowed to initialize the timer. When is set to Disabled (the

 

default), the timer will have no effect on the system.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Dell PowerEdge FC630 Page Contents Installing and removing sled components Troubleshooting your system Using System Diagnostics 102 Jumpers and connectors 104Technical specifications 107 Getting help 112 Front-panel features and indicators About your systemUsing USB diskette or USB DVD/CD drives Hard-drive/SSD indicator patternsIDRAC Direct LED indicator codes Hard-drive/SSD indicatorsIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up your system Setting up and configuring the iDRAC IP addressLogging in to iDRAC Installing the operating system Page About System Setup Navigation keysEntering System Setup System Setup Main MenuSystem Bios screen System Information screen System Memory screenProcessor Settings screen ATSSata Settings screen Post Page Boot Settings screen Network Settings screenIntegrated Devices screen Serial Communication screen System Profile Settings screen C1ESystem Security Settings screen Miscellaneous Settings screen Secure Boot Custom Policy Settings screenPage About Boot Manager About Dell Lifecycle Controller Changing the boot orderEntering Boot Manager Boot Manager main menuChoosing the system boot mode Assigning a system and/or setup passwordUsing your system password to secure your system Operating with a setup password enabled IDRAC Settings utilityEmbedded systems management Entering the iDRAC Settings utility Safety instructions Recommended toolsBefore working inside your system After working inside your systemRemoving and installing a sled Removing the sledO connector cover Installing the sled Removing and installing the sledInside the sled NDCCooling shroud Removing the cooling shroudInstalling the cooling shroud Processor/DIMM blankRemoving a processor/DIMM blank Installing a processor/DIMM blank Removing and installing a processor/DIMM blankSystem memory LrdimmProcessor General memory-module installation guidelines Mode-specific guidelines Advanced ECC LockstepSample memory configurations Memory configurations two processors Removing memory modules Installing memory modules Removing the memory modulePCIe mezzanine card Removing a PCIe mezzanine cardRemoving and installing a PCIe mezzanine card Installing a PCIe mezzanine card Idsdm card optionalReplacing an SD card Ensure that you read the Safety instructions Internal USB key Replacing an SD cardReplacing the internal USB key Removing and installing the Idsdm card Removing the Idsdm cardInstalling the Idsdm card RSPI card optional Removing the rSPI cardInstalling the rSPI card SD vFlash cardReplacing the SD vFlash card Network Daughter Card Removing the Network Daughter CardInstall the NDC. See Installing the Network Daughter Card Installing the Network Daughter Card ProcessorsRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing a processor Installing and removing a processorPage Applying thermal grease on the top of the processor Hard drive/SSD installation guidelines Hard drives/SSDsHard-drive/SSD bay numbering Removing and installing a hard drive/SSD Removing a hard drive/SSDInstalling a hard drive/SSD Removing a hard-drive/SSD blankHard-drive/SSD blank Release latch Installing a hard-drive/SSD blank Shutdown procedure for servicing a hard drive/SSDConfiguring the boot drive Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Installing a 1.8 inch SSD in a 1.8 inch SSD carrier Removing the hard-drive/SSD cageInstalling the hard-drive/SSD cage Removing and installing a hard-drive/SSD cageHard-drive backplane Removing the hard-drive/SSD backplaneRemoving and installing the hard-drive/SSD backplane Installing the hard-drive/SSD backplane Perc H730P slim card Removing a Perc H730P slim cardInstalling a Perc H730P slim card Removing and installing a Perc H730P slim cardStorage controller card Removing the PCIe extender/storage controller cardPage Installing the PCIe extender/storage controller card Nvram backup battery Replacing the Nvram backup batteryReplacing the Nvram backup battery System board Removing the system boardPage Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Installing the Trusted Platform Module Trusted Platform ModuleRe-enabling the TPM for BitLocker users Re-enabling the TPM for TXT usersTroubleshooting your system Troubleshooting hard drives Troubleshooting USB devicesTroubleshooting Solid State Drives Troubleshooting an internal SD card Troubleshooting processorsTroubleshooting the system board Troubleshooting the Nvram backup batteryDiagnostic messages System messagesAlert messages Dell Embedded System Diagnostics When to use the Embedded System DiagnosticsRunning the Embedded System Diagnostics Running Embedded System Diagnostics from an external media System diagnostics controlsJumpers and connectors System board jumper settingsSystem board connectors CPU1Disabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Page Locating your system Service Tag Contacting DellDocumentation feedback 113
Top Page Image Contents