Dell E02B owner manual Hard-drive backplane, Removing the hard-drive/SSD backplane

Page 79

NOTE: You must remove the hard-drive/SSD cage to replace a faulty hard-drive/SSD cage or service other components inside the system.

1.Ensure that you read the Safety instructions.

2.Keep the #1 Phillips screwdriver ready.

3.Remove the hard-drive/SSD cage, see Removing the hard-drive/SSD cage.

Steps

1.Align the slots on the sides of the hard-drive/SSD cage with the standoffs on the chassis.

2.Lower the hard-drive/SSD cage into the chassis until the slots on the hard-drive/SSD cage engage with the standoffs on the chassis.

3.Slide the hard-drive/SSD cage into the chassis till it clicks into position.

4.Install the two screws to secure the hard-drive/SSD cage to the chassis.

Next steps

1.Install the hard-drive/SSD backplane. See Installing the hard-drive/SSD backplane.

2.Install the hard drive/SSDs.

3.Follow the procedure listed in After working inside your system.

Related Links

Installing a hard drive/SSD

Hard-drive backplane

Removing the hard-drive/SSD backplane

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1.Ensure that you read the Safety instructions.

2.Keep the #2 Phillips screwdriver ready.

3.Follow the procedure listed in Before working inside your system.

CAUTION: To prevent damage to the hard drives/SSDs and the hard-drive/SSD backplane, you must remove the hard drives/SSDs from the sled before removing the hard-drive/SSD backplane.

CAUTION: You must note the number of each hard drive/SSD and temporarily label them before removal so that you can replace them in the same locations.

4.Remove the hard drive(s)/SSD(s).

Steps

1.Loosen the two retention screws securing the hard-drive/SSD backplane to the hard-drive/SSD cage.

2.Lift the hard-drive/SSD backplane by its edges till the guide pin on the hard-drive/SSD cage disengages with the guide on the hard-drive/SSD backplane.

79

Image 79

Contents Dell PowerEdge FC630 Page Contents Installing and removing sled components Troubleshooting your system Jumpers and connectors 104 Using System Diagnostics 102Technical specifications 107 Getting help 112 About your system Front-panel features and indicatorsHard-drive/SSD indicator patterns Using USB diskette or USB DVD/CD drivesHard-drive/SSD indicators IDRAC Direct LED indicator codesIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up and configuring the iDRAC IP address Setting up your systemLogging in to iDRAC Installing the operating system Page Navigation keys About System SetupSystem Setup Main Menu Entering System SetupSystem Bios screen System Memory screen System Information screenATS Processor Settings screenSata Settings screen Post Page Network Settings screen Boot Settings screenIntegrated Devices screen Serial Communication screen C1E System Profile Settings screenSystem Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screenPage Boot Manager main menu About Boot ManagerAbout Dell Lifecycle Controller Changing the boot order Entering Boot ManagerAssigning a system and/or setup password Choosing the system boot modeUsing your system password to secure your system IDRAC Settings utility Operating with a setup password enabledEmbedded systems management Entering the iDRAC Settings utility After working inside your system Safety instructionsRecommended tools Before working inside your systemRemoving the sled Removing and installing a sledO connector cover Removing and installing the sled Installing the sledNDC Inside the sledRemoving the cooling shroud Cooling shroudProcessor/DIMM blank Installing the cooling shroudRemoving a processor/DIMM blank Removing and installing a processor/DIMM blank Installing a processor/DIMM blankLrdimm System memoryProcessor General memory-module installation guidelines Advanced ECC Lockstep Mode-specific guidelinesSample memory configurations Memory configurations two processors Removing memory modules Removing the memory module Installing memory modulesRemoving a PCIe mezzanine card PCIe mezzanine cardRemoving and installing a PCIe mezzanine card Idsdm card optional Installing a PCIe mezzanine cardReplacing an SD card Ensure that you read the Safety instructions Replacing an SD card Internal USB keyReplacing the internal USB key Removing the Idsdm card Removing and installing the Idsdm cardInstalling the Idsdm card Removing the rSPI card RSPI card optionalSD vFlash card Installing the rSPI cardReplacing the SD vFlash card Removing the Network Daughter Card Network Daughter CardInstall the NDC. See Installing the Network Daughter Card Processors Installing the Network Daughter CardRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing and removing a processor Installing a processorPage Applying thermal grease on the top of the processor Hard drives/SSDs Hard drive/SSD installation guidelinesHard-drive/SSD bay numbering Removing a hard drive/SSD Removing and installing a hard drive/SSDRemoving a hard-drive/SSD blank Installing a hard drive/SSDHard-drive/SSD blank Release latch Shutdown procedure for servicing a hard drive/SSD Installing a hard-drive/SSD blankConfiguring the boot drive Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Removing the hard-drive/SSD cage Installing a 1.8 inch SSD in a 1.8 inch SSD carrierRemoving and installing a hard-drive/SSD cage Installing the hard-drive/SSD cageRemoving the hard-drive/SSD backplane Hard-drive backplaneRemoving and installing the hard-drive/SSD backplane Installing the hard-drive/SSD backplane Removing a Perc H730P slim card Perc H730P slim cardRemoving and installing a Perc H730P slim card Installing a Perc H730P slim cardRemoving the PCIe extender/storage controller card Storage controller cardPage Installing the PCIe extender/storage controller card Replacing the Nvram backup battery Nvram backup batteryReplacing the Nvram backup battery Removing the system board System boardPage Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Trusted Platform Module Installing the Trusted Platform ModuleRe-enabling the TPM for TXT users Re-enabling the TPM for BitLocker usersTroubleshooting your system Troubleshooting USB devices Troubleshooting hard drivesTroubleshooting Solid State Drives Troubleshooting processors Troubleshooting an internal SD cardTroubleshooting the Nvram backup battery Troubleshooting the system boardSystem messages Diagnostic messagesAlert messages When to use the Embedded System Diagnostics Dell Embedded System DiagnosticsRunning the Embedded System Diagnostics System diagnostics controls Running Embedded System Diagnostics from an external mediaSystem board jumper settings Jumpers and connectorsCPU1 System board connectorsDisabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Page Contacting Dell Locating your system Service TagDocumentation feedback 113