Dell E02B owner manual Idsdm card optional, Installing a PCIe mezzanine card, Replacing an SD card

Page 53

Installing a PCIe mezzanine card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

NOTE: You must remove the PCIe mezzanine card to replace a faulty PCIe mezzanine card or service other components inside the system.

1.Ensure that you read the Safety instructions.

2.Remove the PCIe mezzanine card. See Removing a PCIe mezzanine card.

Steps

1.Open the PCIe mezzanine card retention latch by pressing the release tab on the retention latch and lift the end of the latch.

2.If present, remove the connector cover from the PCIe mezzanine card bay.

CAUTION: To prevent damage to the PCIe mezzanine card, you must hold the card only by its edges.

3.Align the two connectors on the PCIe mezzanine card with the connectors on the system board.

4.Press down the PCIe mezzanine card till the connectors on the card completely engage with the corresponding connectors.

The retention bracket on the side of the chassis latches onto the PCIe mezzanine card.

5.Close the retention latch.

Next steps

Follow the procedure listed in After working inside your system.

Related Links

Removing the sled

Installing the sled

IDSDM card (optional)

The Internal Dual SD Module (IDSDM) card provides two SD card slots and a USB interface dedicated for the embedded hypervisor. This card offers the following features:

Dual card operation — maintains a mirrored configuration using SD cards in both slots and provides redundancy.

Single card operation — single card operation is supported, but without redundancy.

Replacing an SD card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

53

Image 53
Contents Dell PowerEdge FC630 Page Contents Installing and removing sled components Troubleshooting your system Technical specifications 107 Getting help 112 Using System Diagnostics 102Jumpers and connectors 104 About your system Front-panel features and indicatorsHard-drive/SSD indicator patterns Using USB diskette or USB DVD/CD drivesHard-drive/SSD indicators IDRAC Direct LED indicator codesIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up and configuring the iDRAC IP address Setting up your systemLogging in to iDRAC Installing the operating system Page Navigation keys About System SetupSystem Bios screen Entering System SetupSystem Setup Main Menu System Memory screen System Information screenATS Processor Settings screenSata Settings screen Post Page Network Settings screen Boot Settings screenIntegrated Devices screen Serial Communication screen C1E System Profile Settings screenSystem Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screenPage About Dell Lifecycle Controller Changing the boot order About Boot ManagerEntering Boot Manager Boot Manager main menuAssigning a system and/or setup password Choosing the system boot modeUsing your system password to secure your system Embedded systems management Operating with a setup password enabledIDRAC Settings utility Entering the iDRAC Settings utility Recommended tools Safety instructionsBefore working inside your system After working inside your systemRemoving the sled Removing and installing a sledO connector cover Removing and installing the sled Installing the sledNDC Inside the sledRemoving the cooling shroud Cooling shroudRemoving a processor/DIMM blank Installing the cooling shroudProcessor/DIMM blank Removing and installing a processor/DIMM blank Installing a processor/DIMM blankLrdimm System memoryProcessor General memory-module installation guidelines Advanced ECC Lockstep Mode-specific guidelinesSample memory configurations Memory configurations two processors Removing memory modules Removing the memory module Installing memory modulesRemoving a PCIe mezzanine card PCIe mezzanine cardRemoving and installing a PCIe mezzanine card Replacing an SD card Installing a PCIe mezzanine cardIdsdm card optional Ensure that you read the Safety instructions Replacing an SD card Internal USB keyReplacing the internal USB key Removing the Idsdm card Removing and installing the Idsdm cardInstalling the Idsdm card Removing the rSPI card RSPI card optionalReplacing the SD vFlash card Installing the rSPI cardSD vFlash card Removing the Network Daughter Card Network Daughter CardInstall the NDC. See Installing the Network Daughter Card Processors Installing the Network Daughter CardRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing and removing a processor Installing a processorPage Applying thermal grease on the top of the processor Hard-drive/SSD bay numbering Hard drive/SSD installation guidelinesHard drives/SSDs Removing a hard drive/SSD Removing and installing a hard drive/SSDRemoving a hard-drive/SSD blank Installing a hard drive/SSDHard-drive/SSD blank Release latch Configuring the boot drive Installing a hard-drive/SSD blankShutdown procedure for servicing a hard drive/SSD Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Removing the hard-drive/SSD cage Installing a 1.8 inch SSD in a 1.8 inch SSD carrierRemoving and installing a hard-drive/SSD cage Installing the hard-drive/SSD cageRemoving the hard-drive/SSD backplane Hard-drive backplaneRemoving and installing the hard-drive/SSD backplane Installing the hard-drive/SSD backplane Removing a Perc H730P slim card Perc H730P slim cardRemoving and installing a Perc H730P slim card Installing a Perc H730P slim cardRemoving the PCIe extender/storage controller card Storage controller cardPage Installing the PCIe extender/storage controller card Replacing the Nvram backup battery Nvram backup batteryReplacing the Nvram backup battery Removing the system board System boardPage Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Trusted Platform Module Installing the Trusted Platform ModuleRe-enabling the TPM for TXT users Re-enabling the TPM for BitLocker usersTroubleshooting your system Troubleshooting USB devices Troubleshooting hard drivesTroubleshooting Solid State Drives Troubleshooting processors Troubleshooting an internal SD cardTroubleshooting the Nvram backup battery Troubleshooting the system boardAlert messages Diagnostic messagesSystem messages Running the Embedded System Diagnostics Dell Embedded System DiagnosticsWhen to use the Embedded System Diagnostics System diagnostics controls Running Embedded System Diagnostics from an external mediaSystem board jumper settings Jumpers and connectorsCPU1 System board connectorsDisabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Page Documentation feedback Locating your system Service TagContacting Dell 113