Dell E02B owner manual Storage controller card, Removing the PCIe extender/storage controller card

Page 84

Steps

1.If installed, remove the PERC H730P slim card blank.

2.Press the release latch on the side of the chassis to the unlock position.

NOTE: Ensure that all the memory-module ejectors are in the closed position.

3.Align the slots on the PERC H730P slim card with the standoffs on the side of the chassis.

4.Lower the PERC H730P slim card into the chassis until the slots on the card engage with the standoffs on the side of the chassis.

5.Press the release latch to the lock position to secure the card firmly on the chassis. The PERC H730P slim card connects to the backplane connector.

6.Hold the pull tag on the PERC H730 slim-card cable connector and route the cable between the memory-module ejectors.

7.Align the retention screws on the PERC H730P slim-card cable connector with the screw holes on the system board connector.

8.Tighten the two retention screws to secure the PERC H730P slim-card cable connector on the system board.

Next steps

Follow the procedure listed in After working inside your system.

Storage controller card

Your system includes a dedicated expansion-card slot on the system board for a storage controller card that provides the integrated storage subsystem for your system’s hard drives. The storage controller card supports SSD/SAS/SATA hard drives.

NOTE: The storage controller card is located underneath the hard-drive/SSD cage.

Removing the PCIe extender/storage controller card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

NOTE: PCIe extender/storage controller card is supported on systems with the SAS backplanes.

1.Ensure that you read the Safety instructions.

2.Keep the #2 Phillips screwdriver ready.

3.Follow the procedure listed in Before working inside your system.

4.Remove the following:

a.hard drives/SSDs

b.hard-drive/SSD backplane

c.hard-drive/SSD cage

84

Image 84

Contents Dell PowerEdge FC630 Page Contents Installing and removing sled components Troubleshooting your system Using System Diagnostics 102 Jumpers and connectors 104Technical specifications 107 Getting help 112 Front-panel features and indicators About your systemUsing USB diskette or USB DVD/CD drives Hard-drive/SSD indicator patternsIDRAC Direct LED indicator codes Hard-drive/SSD indicatorsIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up your system Setting up and configuring the iDRAC IP addressLogging in to iDRAC Installing the operating system Page About System Setup Navigation keysEntering System Setup System Setup Main MenuSystem Bios screen System Information screen System Memory screenProcessor Settings screen ATSSata Settings screen Post Page Boot Settings screen Network Settings screenIntegrated Devices screen Serial Communication screen System Profile Settings screen C1ESystem Security Settings screen Miscellaneous Settings screen Secure Boot Custom Policy Settings screenPage About Boot Manager About Dell Lifecycle Controller Changing the boot orderEntering Boot Manager Boot Manager main menuChoosing the system boot mode Assigning a system and/or setup passwordUsing your system password to secure your system Operating with a setup password enabled IDRAC Settings utilityEmbedded systems management Entering the iDRAC Settings utility Safety instructions Recommended toolsBefore working inside your system After working inside your systemRemoving and installing a sled Removing the sledO connector cover Installing the sled Removing and installing the sledInside the sled NDCCooling shroud Removing the cooling shroudInstalling the cooling shroud Processor/DIMM blankRemoving a processor/DIMM blank Installing a processor/DIMM blank Removing and installing a processor/DIMM blankSystem memory LrdimmProcessor General memory-module installation guidelines Mode-specific guidelines Advanced ECC LockstepSample memory configurations Memory configurations two processors Removing memory modules Installing memory modules Removing the memory modulePCIe mezzanine card Removing a PCIe mezzanine cardRemoving and installing a PCIe mezzanine card Installing a PCIe mezzanine card Idsdm card optionalReplacing an SD card Ensure that you read the Safety instructions Internal USB key Replacing an SD cardReplacing the internal USB key Removing and installing the Idsdm card Removing the Idsdm cardInstalling the Idsdm card RSPI card optional Removing the rSPI cardInstalling the rSPI card SD vFlash cardReplacing the SD vFlash card Network Daughter Card Removing the Network Daughter CardInstall the NDC. See Installing the Network Daughter Card Installing the Network Daughter Card ProcessorsRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing a processor Installing and removing a processorPage Applying thermal grease on the top of the processor Hard drive/SSD installation guidelines Hard drives/SSDsHard-drive/SSD bay numbering Removing and installing a hard drive/SSD Removing a hard drive/SSDInstalling a hard drive/SSD Removing a hard-drive/SSD blankHard-drive/SSD blank Release latch Installing a hard-drive/SSD blank Shutdown procedure for servicing a hard drive/SSDConfiguring the boot drive Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Installing a 1.8 inch SSD in a 1.8 inch SSD carrier Removing the hard-drive/SSD cageInstalling the hard-drive/SSD cage Removing and installing a hard-drive/SSD cageHard-drive backplane Removing the hard-drive/SSD backplaneRemoving and installing the hard-drive/SSD backplane Installing the hard-drive/SSD backplane Perc H730P slim card Removing a Perc H730P slim cardInstalling a Perc H730P slim card Removing and installing a Perc H730P slim cardStorage controller card Removing the PCIe extender/storage controller cardPage Installing the PCIe extender/storage controller card Nvram backup battery Replacing the Nvram backup batteryReplacing the Nvram backup battery System board Removing the system boardPage Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Installing the Trusted Platform Module Trusted Platform ModuleRe-enabling the TPM for BitLocker users Re-enabling the TPM for TXT usersTroubleshooting your system Troubleshooting hard drives Troubleshooting USB devicesTroubleshooting Solid State Drives Troubleshooting an internal SD card Troubleshooting processorsTroubleshooting the system board Troubleshooting the Nvram backup batteryDiagnostic messages System messagesAlert messages Dell Embedded System Diagnostics When to use the Embedded System DiagnosticsRunning the Embedded System Diagnostics Running Embedded System Diagnostics from an external media System diagnostics controlsJumpers and connectors System board jumper settingsSystem board connectors CPU1Disabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Page Locating your system Service Tag Contacting DellDocumentation feedback 113