Dell E02B owner manual Boot Settings screen, Network Settings screen

Page 23

Menu Item

Description

 

 

Capacity

Displays the total capacity of the hard drive. The field is undefined for

 

removable media devices such as optical drives.

Port J

Sets the drive type of the selected device. For Embedded SATA settings

 

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

 

to turn off BIOS support.

 

For AHCI mode or RAID mode, BIOS always enables support.

Model

Displays the drive model of the selected device.

Drive Type

Displays the type of drive attached to the SATA port.

Capacity

Displays the total capacity of the hard drive. The field is undefined for

 

removable media devices such as optical drives.

Boot Settings screen

You can use the Boot Settings screen to set the Boot mode to either BIOS or UEFI. It also allows you to specify the boot order.

You can view the Boot Settings screen by clicking System Setup Main Menu → System BIOS → Boot Settings.

Menu Item

Description

 

 

Boot Mode

Enables you to set the boot mode of the system.

 

CAUTION: Switching the boot mode may prevent the system from

 

booting if the operating system is not installed in the same boot

 

mode.

 

NOTE: Setting this field to UEFI disables the BIOS Boot Settings

 

menu. Setting this field to BIOS disables the UEFI Boot Settings

 

menu.

 

If the operating system supports UEFI, you can set this option to UEFI.

 

Setting this field to BIOS allows compatibility with non-UEFI operating

 

systems. By default, the Boot Mode option is set to BIOS.

Boot Sequence Retry

Enables or disables the Boot Sequence Retry feature. If this field is

 

enabled and the system fails to boot, the system reattempts the boot

 

sequence after 30 seconds. By default, the Boot Sequence Retry option

 

is set to Enabled.

Hard-Disk Failover

Specifies which devices in the Hard-Disk Drive Sequence are attempted

 

in the boot sequence. When the option is Disabled, only the first hard

 

disk device in the list is attempted to boot. When set to Enabled, all hard

 

disk devices are attempted in order, as listed in the Hard-Disk Drive

 

Sequence. This option is not enabled for UEFI Boot Mode.

Boot Option Settings

Configures the boot sequence and the boot devices.

Network Settings screen

You can use the Network Settings screen to modify PXE device settings. Network Settings are only available in UEFI boot mode. BIOS does not control network settings in the BIOS boot mode. For BIOS boot mode, the network settings are handled by the network controllers option ROM.

You can view the Network Settings screen by clicking System Setup Main Menu → System BIOS → Network Settings.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Dell PowerEdge FC630 Page Contents Installing and removing sled components Troubleshooting your system Technical specifications 107 Getting help 112 Using System Diagnostics 102Jumpers and connectors 104 About your system Front-panel features and indicatorsHard-drive/SSD indicator patterns Using USB diskette or USB DVD/CD drivesHard-drive/SSD indicators IDRAC Direct LED indicator codesIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up and configuring the iDRAC IP address Setting up your systemLogging in to iDRAC Installing the operating system Page Navigation keys About System SetupSystem Bios screen Entering System SetupSystem Setup Main Menu System Memory screen System Information screenATS Processor Settings screenSata Settings screen Post Page Network Settings screen Boot Settings screenIntegrated Devices screen Serial Communication screen C1E System Profile Settings screenSystem Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screenPage Boot Manager main menu About Boot ManagerAbout Dell Lifecycle Controller Changing the boot order Entering Boot ManagerAssigning a system and/or setup password Choosing the system boot modeUsing your system password to secure your system Embedded systems management Operating with a setup password enabledIDRAC Settings utility Entering the iDRAC Settings utility After working inside your system Safety instructionsRecommended tools Before working inside your systemRemoving the sled Removing and installing a sledO connector cover Removing and installing the sled Installing the sledNDC Inside the sledRemoving the cooling shroud Cooling shroudRemoving a processor/DIMM blank Installing the cooling shroudProcessor/DIMM blank Removing and installing a processor/DIMM blank Installing a processor/DIMM blankLrdimm System memoryProcessor General memory-module installation guidelines Advanced ECC Lockstep Mode-specific guidelinesSample memory configurations Memory configurations two processors Removing memory modules Removing the memory module Installing memory modulesRemoving a PCIe mezzanine card PCIe mezzanine cardRemoving and installing a PCIe mezzanine card Replacing an SD card Installing a PCIe mezzanine cardIdsdm card optional Ensure that you read the Safety instructions Replacing an SD card Internal USB keyReplacing the internal USB key Removing the Idsdm card Removing and installing the Idsdm cardInstalling the Idsdm card Removing the rSPI card RSPI card optionalReplacing the SD vFlash card Installing the rSPI cardSD vFlash card Removing the Network Daughter Card Network Daughter CardInstall the NDC. See Installing the Network Daughter Card Processors Installing the Network Daughter CardRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing and removing a processor Installing a processorPage Applying thermal grease on the top of the processor Hard-drive/SSD bay numbering Hard drive/SSD installation guidelinesHard drives/SSDs Removing a hard drive/SSD Removing and installing a hard drive/SSDRemoving a hard-drive/SSD blank Installing a hard drive/SSDHard-drive/SSD blank Release latch Configuring the boot drive Installing a hard-drive/SSD blankShutdown procedure for servicing a hard drive/SSD Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Removing the hard-drive/SSD cage Installing a 1.8 inch SSD in a 1.8 inch SSD carrierRemoving and installing a hard-drive/SSD cage Installing the hard-drive/SSD cageRemoving the hard-drive/SSD backplane Hard-drive backplaneRemoving and installing the hard-drive/SSD backplane Installing the hard-drive/SSD backplane Removing a Perc H730P slim card Perc H730P slim cardRemoving and installing a Perc H730P slim card Installing a Perc H730P slim cardRemoving the PCIe extender/storage controller card Storage controller cardPage Installing the PCIe extender/storage controller card Replacing the Nvram backup battery Nvram backup batteryReplacing the Nvram backup battery Removing the system board System boardPage Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Trusted Platform Module Installing the Trusted Platform ModuleRe-enabling the TPM for TXT users Re-enabling the TPM for BitLocker usersTroubleshooting your system Troubleshooting USB devices Troubleshooting hard drivesTroubleshooting Solid State Drives Troubleshooting processors Troubleshooting an internal SD cardTroubleshooting the Nvram backup battery Troubleshooting the system boardAlert messages Diagnostic messagesSystem messages Running the Embedded System Diagnostics Dell Embedded System DiagnosticsWhen to use the Embedded System Diagnostics System diagnostics controls Running Embedded System Diagnostics from an external mediaSystem board jumper settings Jumpers and connectorsCPU1 System board connectorsDisabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Page Documentation feedback Locating your system Service TagContacting Dell 113
Top Page Image Contents