Furuno DS-60 installation manual Wiring, Precautions for cable installation

Page 29

2.WIRING

Refer to the interconnection diagram at the back of this manual to connect cables.

Distributor

DS-610Remote Controller RD-501/

Dimmer Controller RD-502

TTYCYS-4

Display Unit

(main)

DS-600

100-240 VAC (DPYC-2.5)

DS-340 (CO-SPEVV-SB-C)

ANALOG VOLTAGE OUT (TTYCS-1) ANALOG CURRENT OUT (TTYCS-1)

KP IN/OUT (TTYCS-1, x2)

ALARM SYSTEM ANALOG METER OUT (TTYCYS-1Q, x2)

DIGITAL OUT

DIGITAL OUT

LOG/CONTACT, 200 pulse (DPYCY-1.5, x4) IEC61162/IN (TTYCS-1, x3)

IEC61162/OUT (TTYCS-1, x5)

TTYCYS-4 or TTYCS-4

 

 

(Max. 150 m)

 

 

Display Unit (sub) DS-600, RD-20/50 (x5)

 

 

Transceiver Unit

Junction Box

DS-620

DS-640 (option)

 

 

TTYCY-4S*

TTYCY-4S*

 

 

DPYCY-4.0*

 

 

DPYCY-4.0*

 

 

 

Transducer cable

Transducer

(30 m/40 m/50 m/60 m)

DS-630/631

*The cable length between DS-620 and DS-610 must be less than 500 m.

Note: For details of JIS (Japan Industrial Standard) cables, see APPENDIX 2.

Precautions for cable installation

Observe the following guidelines to prevent noise, interference problem.

The transducer cable carries very weak signals (amplitude less than 0.1 μV), which are easily interfered by noise. The need for a good ground cannot be overempha- sized.

Locate DS-60 cables away from the transmission antenna cable or radio equip- ment.

Locate the DS-60 cables away from the power cables mentioned below. Also, sep- arate cables at least 400 mm when the cables are run parallel with power cables.

Cable carrying more than a few kilowatts power to fluctuating loads

Cable carrying switching waves generated by thyristor, etc.

2-1

Image 29
Contents Iii Installation Manual00017233810 Safety Instructions System Configurations Standard supply Equipment ListsOptional Supply Flush mount Display Unit DS-600Mounting consideration Desktop or table underside mount Hanger assembly Type OP26-8, Code NoHow to set the cosmetic cap and alarm lid assy Transceiver Unit DS-620 Installation considerationsDistributor Unit DS-610 Transducer Installation locationTransducer tank DS-660, sectional view Installation using the transducer tank DS-660Hex. bolt 15 Seal washer Fixing plate Hex. bolt M6x20 Spring washer M6 Cable assy Metal fixing Transducer tank, sectional view DS-661 gate valve, sectional view Installation with gate valve DS-661Installation Installation Installation How to open the gate valve Junction Box DS-640 option Mounting considerations Mounting procedureApply silicon rubber to M10 bolts as shown below Pass the cable through the cable gland as shown below How to change orientation of the front cover of DS-605 Remote Controller RD-501/Dimmer Controller RD-502 optionRate-of-Turn Gyro DS-340 option Leveling adjustmentThis page is intentionally left blank Precautions for cable installation WiringTop cover Cable clamps, entrances Connection of Wago connectorTB3 TB1 TB5 TB2 TB4 TB8 DS-610 Distributor Unit DS-620 Transceiver unit DS-600 Display unit DS-600, example of connection DS-640 Junction Box Junction Box DS-640, optionHow to Use the Service Menu Menu SettingsMenu item Meaning Option How to set ship’s data How to Set the System MenuHow to show the System menu Meaning Setting range How to enter offset valuesHow to correct the ship’s speed This page is intentionally left blank Calculation with transit posts AP-1Milepost run Calculation with DS-60 AP-2AP-3 AP-4 Appendix 2 JIS Cable Guide+/05+105+0&4#9+014440%10. #% #6 #6 52#42#465.+5614 5 #%%5514+5 Page Page Page Dec/08 R.Esumi Mar/09 R.Esumi Dec/08 R.Esumi 14/Jul/09 R.Esumi 14/Jul/09 R.Esumi 26/Oct/09 R.Esumi Dec/08 R.Esumi Dec/08 R.Esumi Dec/08 R.Esumi Doppler Sonar