Furuno DS-60 installation manual Remote Controller RD-501/Dimmer Controller RD-502 option

Page 26

1. INSTALLATION

How to change orientation of the front cover of DS-605

The front cover of the DS-605 can be oriented up, down, right or left. To change the orientation of the front cover, do the following.

Note: Set the front cover so the FURUNO logo on the cover is right side up. The drain hole must be down.

1.Remove eight screws from two hinges.

2.Remove two screws from the latch.

3.Remove the hinges and the hidden lids for fixing hole of latch in consideration of the opening direction.The hidden lids for fixing hole of latch are taped on each side.

4.Orient the front cover as desired and fix the hinges and latch.

Hinge

Latch

Screws for hinge

Hidden lids for fixing hole of latch (four sides)

1.7Remote Controller RD-501/Dimmer Controller RD-502 (option)

The optional remote controller RD-501 and dimmer controller RD-502 can be flush mounted in a panel. The size and the mounting procedure are shared by RD-501 and RD-502. For the mounting location, refer to the mounting considerations for the display unit in section1.2.

Note: Before you fasten the display unit to the cutout, first connect the cables referring to chapter 2.

1.Make a cutout in the mounting location (88 mm (width) x 76 mm (height)).

2.Make four holes of 4 mm diameter in the locations indicated in the illustration below.

3.Set the remote controller or dimmer controller to the cutout. Insert four binding head screws (M3x12) from the front side then fasten the unit with four sets of flat washers, spring washers and hexagonal nuts from the rear side.

86 ± 0.5 (3.39”)

88 ± 1.0 (3.46”)

76 ± 1.0 (2.99”)

DISP UNIT MODE

REMOTE CONTROLLER

RD-501

86 ± 0.5 (3.39”)

Fixing hole (4- 4)

1-20

Image 26
Contents Installation Manual Iii00017233810 Safety Instructions System Configurations Equipment Lists Standard supplyOptional Supply Flush mount Display Unit DS-600Mounting consideration Hanger assembly Type OP26-8, Code No Desktop or table underside mountHow to set the cosmetic cap and alarm lid assy Installation considerations Transceiver Unit DS-620Distributor Unit DS-610 Installation location TransducerInstallation using the transducer tank DS-660 Transducer tank DS-660, sectional viewHex. bolt 15 Seal washer Fixing plate Hex. bolt M6x20 Spring washer M6 Cable assy Metal fixing Transducer tank, sectional view Installation with gate valve DS-661 DS-661 gate valve, sectional viewInstallation Installation Installation How to open the gate valve Junction Box DS-640 option Mounting procedure Mounting considerationsApply silicon rubber to M10 bolts as shown below Pass the cable through the cable gland as shown below Remote Controller RD-501/Dimmer Controller RD-502 option How to change orientation of the front cover of DS-605Leveling adjustment Rate-of-Turn Gyro DS-340 optionThis page is intentionally left blank Wiring Precautions for cable installationConnection of Wago connector Top cover Cable clamps, entrancesTB3 TB1 TB5 TB2 TB4 TB8 DS-610 Distributor Unit DS-620 Transceiver unit DS-600 Display unit DS-600, example of connection Junction Box DS-640, option DS-640 Junction BoxMenu Settings How to Use the Service MenuMenu item Meaning Option How to set ship’s data How to Set the System MenuHow to show the System menu How to enter offset values Meaning Setting rangeHow to correct the ship’s speed This page is intentionally left blank Calculation with transit posts AP-1Milepost run AP-2 Calculation with DS-60AP-3 Appendix 2 JIS Cable Guide AP-4+/05+105+0&4#9+014440%10. #% #6 #6 52#42#465.+5614 5 #%%5514+5 Page Page Page Dec/08 R.Esumi Mar/09 R.Esumi Dec/08 R.Esumi 14/Jul/09 R.Esumi 14/Jul/09 R.Esumi 26/Oct/09 R.Esumi Dec/08 R.Esumi Dec/08 R.Esumi Dec/08 R.Esumi Doppler Sonar