Tascam DM-3200 owner manual Viewing a list of location memories, Manual location, Repeat play

Page 100

8 – Remote operation : Location memories

NOTE

If a pre-roll time has been set (“Locate Preroll” on page 98), the controlled device will locate to the loca- tion memory point, minus the value set as the preroll time.

Viewing a list of location memories

To view a popup list of all the location memories which have been stored:

•Press the LOCATE LIST key.

•The location memory source (timecode or MTC) is shown, along with the value of each location memory. The DIRECT indicator also lights.

•Press a number key (from 0 through 9) to locate to a location point on the list while the list is showing.

Manual location

It is also possible to enter a location point manually, (from a cue list, for instance) and locate straight to it.

1Press the MANUAL key so that the indicator lights.

2Use the number keys to enter a number in hh:mm:ss (and optionally frames) format.

3When the ENTER key is pressed, the con- trolled device starts to locate to the location point just entered.

This location point can be stored by pressing the MEMO key so that the indicator flashes, followed by pressing the MANUAL key again.

To locate to this point again after storing the location point, press the MANUAL key, followed by the ENTER key.

Note that the pre-roll time (“Locate Preroll” on page 98) does not apply here.

Repeat play

Location memories 8 and 9 (accessed with the 8 and 9 keys) are used as the start and end points of a repeat loop that can be played by pressing the REPEAT key in the MACHINE CONTROL section.

While the repeat loop is in progress, the indicator flashes while the playback position is outside the

loop points, and lights steadily while it is inside them.

The repeat is always between points 8 and 9, regard- less of their order. These points must be more than 5 seconds apart.

100 TASCAM DM-3200 User’s Manual

Page 99 Page 101
Image 100
Page 99 Page 101
Contents Digital Mixing Console HAZARD, do not Expose this Appliance to Rain or Moisture Important Safety Instructions Contents Routing & assignment ConnectionsChannel modules Specifications EffectsMidi Remote operation17 Channel delay Gate/Expander preset library entriesList of Figures Effects Remote operation Supported transport machine controlIntroduction Computer DAW integrationOther key points Please read this manualIntroduction About the DM-3200 About the DM-3200Channel destinations Mixer channelsIntroduction Unpacking the DM-3200 Unpacking the DM-3200About the manual Introduction About the manualWhat’s in the manual Special notes for touch-sensitive faders Introduction Special notes for touch-sensitive fadersCopyright, etc Introduction The features of the DM-3200 Features of the DM-3200Module & layer control section Modifier sectionLibrary section and CF card slot Machine control sectionSmart keys Basic operational conceptsWhat’s on the screen? Jumping to commonly-used screens Explanation of the top line of screen displaysBasic operational concepts Special controls Special controlsFader layers PODsPOD knobs used in a multi-control Screen GATE/DYN dynamics processor mode Basic operational concepts EncodersEncoders Encoder mappingsReading the encoder indicators Hard left Little less hard Centered Little to Left RightThree indicators Now off Now lit One half-lit No cut or boost Slight boost note Little more boostLowest frequency Middle Little higher Than middleLow shelf High shelf Peak Notch Encoder behaviorFull cut Below nominal Nominal 0dB Above nominal CF cards Basic operational concepts CF cardsFormatting a new card How to shut down the DM-3200 In order to Basic operational concepts Shutting down the DM-3200Shutting down the DM-3200 Important CAUTION!!! Data associated withBasic operational concepts About projects and libraries About projects and librariesCreating a new project Setting the date and timeSystem Managing projects 24 The project managementSaving project data 25 Storing a projectBasic operational concepts Library management Library managementLibrary utilities Target area Target areaSOURCE areaSetup screen Basic operational concepts Naming library entriesNaming library entries Options30 The Setup option screen Basic operational concepts OptionsEncoder Mode Follows Current Screen Current Screen Follows Encoder ModeSEL keys Meter layer Buss AUXSolo Utilities Basic operational concepts UtilitiesUtility copying Switch utility 35 Utility external switch settingsStereo digital I/O Cascade ConnectionsMIDI, control and sync connections Analog connections Connections Analog connectionsMic/line connections Connections Digital connections Digital connectionsAnalog outputs Digital audio I/ODigital I/O setup Digital Setup screenConnections Other connections Slot card configurationOther connections Connections Other connections Connections Clock setting Clock settingFireWire card Normal High-speed InternalCascade Digital in 1/2Yes Routing & assignmentYes Yesb Routing Routing & assignment RoutingInput routing TIP Output routing Insert patching Routing & assignment Channel-to-buss assignment Assignment using the front panelChannel-to-buss assignment Buss assignments with the pan switch Off Non-channel assignments Assignments from Monitoring Routing & assignment MonitoringSelecting the CR source Studio cue source Talkback, etc Oscillator and noise generatorFull-featured modules MetersFirst 24 channel modules Return modulesSoloing Channel modules General principlesGlobal module settings Channel modules Global module settingsChannels Fader control Fader or Master M/F tabsChannel modules Dynamics processors Dynamics processorsShift key Ctrl keyGates input channels Compressor/expandersDecay time Step size Release time Step sizeCompressor/Expander preset library entries Preset dynamics library entriesProgram Name Comment Number Trigger settings Channel modules EQ EQ library 11 EQ library Number Title CommentChannel modules Aux and buss setup Aux and buss setupAux send pan/balance screens linked Channel modules Module setup Module setupMaximum delay ms 44.1 371.5 341.3 88.2 185.7 170.7Phase/trim/delay Stereo linking Mute groups Fader groups Changing surround mode Surround mode is set from the PAN/BAL Surround Mode screenChannel modules Surround operations Surround operationsSurround panning 33 Surround panning pan mode on LFE level Snapshots Channel modules SnapshotsSnapshot library management Storing snapshots Information about a snapshotEffects Setting up the effectsRouting the effects Effects Setting up the effects Tascam effect parametersTC Works effect parameters Effects Effect libraries Preset TC Reverb effectsEffect libraries Number Name LCD indication 024 025026 027Number Name LCD indication 063 064065 066Preset Tascam effects Preset Title LCD indication Comments Guitar CompressorDistortion Tascam effectsPreset Title LCD indication Comments PhaserCompressor ExciterMulti-tap Preset Title LCD indication Comments Delay StereoChorus Pitch changer 100101 106Midi port switching and filtering MidiMidi Program Change messages and the DM-3200 Midi Implementation ChartsProgram Change messages and the DM-3200 Remote operation Selecting devices for transport controlRemote operation Selecting devices for transport control Deleting devices from the listAuto-detection of devices Selecting the control type for the devicesTransport mapping memories Viewing the transport mappings To use a transport mappingEditing a mapping Remote operation Machine control setup Machine control setupRecord Command Type Locate PrerollRemote operation Location memories Location memoriesManual location Viewing a list of location memoriesRepeat play Auto punch operations ALL Input and Auto MONSpecifications Analog audio I/OAssignable Returns BAL 1 through Assignable Sends 1 throughDigital audio I/O Specifications Digital audio I/OMiscellaneous I/O connections Specifications Equalization Physical characteristicsEqualization System performanceSpecifications Dimensional drawing Dimensional drawingMessages and troubleshooting Popup messagesSpecifications Messages and troubleshooting Shown when performing bulk setup of the channel delay time Shown when performing bulk setup of the channel LFE levelShown when undoing or redoing library operations Shown when all grouping layers are to be clearedClock source has been selected, but no signal is present Library preset entry has been recalled compressor/expanderResults of performing a word sync check Valid clock source has been selectedConfirmation when copying automation configuration Confirmation when performing a parameter copy operationConfirmation that the digital trim values are to be updated Groups of 8 busses, or groups of 8 channelsLibrary preset entry has been recalled effect Shown when undoing or redoing effect library operationsInformation about a library preset entry EQ Information about a library preset entry gateConfirmation when changing between Input and Return sources Confirmation that the delay values are to be updatedInformation about a library entry gate Group does not exist to be used as a grouping layerProject to another Project bankConfirmation about the deletion of an automation file Confirmation before deleting dataConfirmation when re-assigning a grouping layer master Confirmation when re-assigning a fader group masterConfirmation when changing a setting Should this changed data be loaded?Digital audio data error from AES card non-audio data Digital audio data error from AES card loss of word syncInformation on a preset snapshot Snapshot preset has been recalledDM-3200 can be rebooted Stored a snapshotChanged Current project cannot be renamedSpecifications Block diagram Block diagramSpecifications Level diagram Level diagramPage Page DM-3200
Related manuals
Manual 2 pages 325 b Manual 4 pages 61.69 Kb

DM-3200 specifications

The Tascam DM-3200 is a versatile digital mixing console renowned for its professional audio capabilities and comprehensive feature set. Launched as a part of Tascam’s acclaimed DM series, this console has become a favorite among recording engineers and musicians for its flexibility and high-quality sound processing.

One of the standout features of the DM-3200 is its ability to handle both analog and digital audio signals seamlessly. With 32 input channels, it provides ample connectivity options that are vital for modern studios. It supports both analog line-level signals and digital inputs via ADAT, AES/EBU, and S/PDIF, which allows for extensive routing and integration with various devices and systems.

The DM-3200 features an 8-bus architecture, which enables users to create complex mixes with ease. Each channel is equipped with a 4-band parametric EQ, offering precise control over the tonal balance of each audio source. The onboard effects processing includes virtual effects such as reverb, delay, and modulation, which enhances the overall sound quality and provides creative options for mixing and mastering.

Another notable aspect of the DM-3200 is its intuitive user interface. The console features an LCD display alongside faders, knobs, and buttons designed for quick and efficient operation. The layout facilitates smooth navigation through menus, making it user-friendly for both novice and experienced engineers.

In terms of recording and playback, the DM-3200 supports 24-bit/96 kHz audio resolution, ensuring high-fidelity sound for both tracking and mixing. This capability makes it suitable for post-production, live sound, and studio work, providing high-quality audio requisite in various applications.

Tascam has integrated advanced automation features into the DM-3200, allowing users to automate fader positions, effects parameters, and more. This feature is particularly beneficial during mixing sessions where precision and repeatability are essential.

Additionally, the DM-3200 is capable of digital multitrack recording and can interface seamlessly with DAWs via FireWire, enhancing its versatility in a hybrid studio environment. Whether you are recording a band, mixing a podcast, or producing a film score, the Tascam DM-3200 stands out as a powerful tool in professional audio production.
Top Page Image Contents