Tascam DM-3200 owner manual Preset dynamics library entries, Program Name Comment Number

Page 64

5 – Channel modules : Dynamics processors

Auto make-up(AUTOmk-up), controlled by the ENTER key. This is used if the compression settings have resulted in gain reduction. Not shown if the pro- cessor is being used as an expander.

Output gain (OUTGAIN), controlled by the POD 4 knob on the last row (grayed out if the auto make-up above is on). Variable from -20dBto +20dB in 1 dB steps. Not shown if the processor is being used as an expander.

Library jump buttons There are two such on- screen library jump buttons on channels 1 through 32 (gate and compressor/expander). Other modules only have the compressor/expander jump keys.

These buttons are labeled GATE... LIBand C/E... LIBrespectively.

When pressed, the appropriate library screen is brought up, where the current settings can be stored for future use, or preset or previously-stored settings can be recalled for use in the project.

Preset dynamics library entries

The following preset entries are provided either to be used “as-is”, or to be used as templates or starting points for experimentation.

These library entries are read-only (marked with an inverse R on the display), and may not be overwritten. However, it is possible to load the entries, edit the parameters, and then store them to a different library entry.

As always, there are no hard and fast rules as to what “works”. Feel free to use the settings in a variety of contexts and change them as seems appropriate to you.

Compressor/expander library entries Use these settings for the compressor/expander either “as is” or edit them to your needs and store them as part of the project.

Program

Name

Comment

Number

 

 

 

 

 

000

Sample Snare

For use with snare drums

 

 

 

001

Slap Bass

For use with slap-type bass inputs

 

 

 

002

Electric Bass

For use with electric bass guitar

 

 

 

003

Wood Bass

For use with upright bass (double-bass or contra-bass)

 

 

 

004

Synth. Bass 1

For use with synthesized bass lines

 

 

 

005

Synth. Bass 2

For use with synthesized bass lines

 

 

 

006

Acoustic Guitar

To be used with acoustic guitars (nylon or steel-strung)

 

 

 

007

Electric Guitar 1

For use with electric guitars

 

 

 

008

Electric Guitar 2

For use with electric guitars

 

 

 

009

Electric Guitar 3

For use with electric guitars

 

 

 

010

Brass

Effective with brass (horn) sections, etc.

 

 

 

011

Vocal 1

Use with vocal lines

 

 

 

012

Vocal 2

Use with vocal lines

 

 

 

013

Total Comp 1

Overall compressor setting

 

 

 

014

Total Comp 2

Overall compressor setting

 

 

 

015

Total Comp 3

Overall compressor setting

 

 

 

016

Post Pro.1

Useful in post-production environments

 

 

 

017

Post Pro.2

Useful in post-production environments

 

 

 

018

Narration

For the spoken word

 

 

 

019

Expander1

Expander setting

 

 

 

020

Expander2

Another expander setting

 

 

 

021

Slow Attack

An expander with a slow attack

 

 

 

022

E Guitar Clean1

Expander setting suitable for electric guitar

 

 

 

Table 5.7: Compressor/Expander preset library entries

64 TASCAM DM-3200 User’s Manual

Image 64
Contents Digital Mixing Console HAZARD, do not Expose this Appliance to Rain or Moisture Important Safety Instructions Contents Routing & assignment ConnectionsChannel modules Specifications EffectsMidi Remote operation17 Channel delay Gate/Expander preset library entriesList of Figures Effects Remote operation Supported transport machine controlIntroduction Computer DAW integrationOther key points Please read this manualIntroduction About the DM-3200 About the DM-3200Channel destinations Mixer channelsIntroduction Unpacking the DM-3200 Unpacking the DM-3200About the manual Introduction About the manualWhat’s in the manual Special notes for touch-sensitive faders Introduction Special notes for touch-sensitive fadersCopyright, etc Introduction The features of the DM-3200 Features of the DM-3200Module & layer control section Modifier sectionLibrary section and CF card slot Machine control sectionSmart keys Basic operational conceptsWhat’s on the screen? Jumping to commonly-used screens Explanation of the top line of screen displaysBasic operational concepts Special controls Special controlsFader layers PODsPOD knobs used in a multi-control Screen GATE/DYN dynamics processor mode Basic operational concepts EncodersEncoders Encoder mappingsReading the encoder indicators Hard left Little less hard Centered Little to Left RightThree indicators Now off Now lit One half-lit No cut or boost Slight boost note Little more boostLowest frequency Middle Little higher Than middleLow shelf High shelf Peak Notch Encoder behaviorFull cut Below nominal Nominal 0dB Above nominal CF cards Basic operational concepts CF cardsFormatting a new card How to shut down the DM-3200 In order to Basic operational concepts Shutting down the DM-3200Shutting down the DM-3200 Important CAUTION!!! Data associated withBasic operational concepts About projects and libraries About projects and librariesCreating a new project Setting the date and timeSystem Managing projects 24 The project managementSaving project data 25 Storing a projectBasic operational concepts Library management Library managementLibrary utilities Target area Target areaSOURCE areaSetup screen Basic operational concepts Naming library entriesNaming library entries Options30 The Setup option screen Basic operational concepts OptionsEncoder Mode Follows Current Screen Current Screen Follows Encoder ModeSEL keys Meter layer Buss AUXSolo Utilities Basic operational concepts UtilitiesUtility copying Switch utility 35 Utility external switch settingsStereo digital I/O Cascade ConnectionsMIDI, control and sync connections Analog connections Connections Analog connectionsMic/line connections Connections Digital connections Digital connectionsAnalog outputs Digital audio I/ODigital I/O setup Digital Setup screenConnections Other connections Slot card configurationOther connections Connections Other connections Connections Clock setting Clock settingFireWire card Normal High-speed InternalCascade Digital in 1/2Yes Routing & assignmentYes Yesb Routing Routing & assignment RoutingInput routing TIP Output routing Insert patching Routing & assignment Channel-to-buss assignment Assignment using the front panelChannel-to-buss assignment Buss assignments with the pan switch Off Non-channel assignments Assignments from Monitoring Routing & assignment MonitoringSelecting the CR source Studio cue source Talkback, etc Oscillator and noise generatorFull-featured modules MetersFirst 24 channel modules Return modulesSoloing Channel modules General principlesGlobal module settings Channel modules Global module settingsChannels Fader control Fader or Master M/F tabsChannel modules Dynamics processors Dynamics processorsShift key Ctrl keyGates input channels Compressor/expandersDecay time Step size Release time Step sizeCompressor/Expander preset library entries Preset dynamics library entriesProgram Name Comment Number Trigger settings Channel modules EQ EQ library 11 EQ library Number Title CommentChannel modules Aux and buss setup Aux and buss setupAux send pan/balance screens linked Channel modules Module setup Module setupMaximum delay ms 44.1 371.5 341.3 88.2 185.7 170.7Phase/trim/delay Stereo linking Mute groups Fader groups Changing surround mode Surround mode is set from the PAN/BAL Surround Mode screenChannel modules Surround operations Surround operationsSurround panning 33 Surround panning pan mode on LFE level Snapshots Channel modules SnapshotsSnapshot library management Storing snapshots Information about a snapshotEffects Setting up the effectsRouting the effects Effects Setting up the effects Tascam effect parametersTC Works effect parameters Effects Effect libraries Preset TC Reverb effectsEffect libraries Number Name LCD indication 024 025026 027Number Name LCD indication 063 064065 066Preset Tascam effects Preset Title LCD indication Comments Guitar CompressorDistortion Tascam effectsPreset Title LCD indication Comments PhaserCompressor ExciterMulti-tap Preset Title LCD indication Comments Delay StereoChorus Pitch changer 100101 106Midi port switching and filtering MidiMidi Program Change messages and the DM-3200 Midi Implementation ChartsProgram Change messages and the DM-3200 Remote operation Selecting devices for transport controlRemote operation Selecting devices for transport control Deleting devices from the listAuto-detection of devices Selecting the control type for the devicesTransport mapping memories Viewing the transport mappings To use a transport mappingEditing a mapping Remote operation Machine control setup Machine control setupRecord Command Type Locate PrerollRemote operation Location memories Location memoriesManual location Viewing a list of location memoriesRepeat play Auto punch operations ALL Input and Auto MONSpecifications Analog audio I/OAssignable Returns BAL 1 through Assignable Sends 1 throughDigital audio I/O Specifications Digital audio I/OMiscellaneous I/O connections Specifications Equalization Physical characteristicsEqualization System performanceSpecifications Dimensional drawing Dimensional drawingMessages and troubleshooting Popup messagesSpecifications Messages and troubleshooting Shown when performing bulk setup of the channel delay time Shown when performing bulk setup of the channel LFE levelShown when undoing or redoing library operations Shown when all grouping layers are to be clearedClock source has been selected, but no signal is present Library preset entry has been recalled compressor/expanderResults of performing a word sync check Valid clock source has been selectedConfirmation when copying automation configuration Confirmation when performing a parameter copy operationConfirmation that the digital trim values are to be updated Groups of 8 busses, or groups of 8 channelsLibrary preset entry has been recalled effect Shown when undoing or redoing effect library operationsInformation about a library preset entry EQ Information about a library preset entry gateConfirmation when changing between Input and Return sources Confirmation that the delay values are to be updatedInformation about a library entry gate Group does not exist to be used as a grouping layerProject to another Project bankConfirmation about the deletion of an automation file Confirmation before deleting dataConfirmation when re-assigning a grouping layer master Confirmation when re-assigning a fader group masterConfirmation when changing a setting Should this changed data be loaded?Digital audio data error from AES card non-audio data Digital audio data error from AES card loss of word syncInformation on a preset snapshot Snapshot preset has been recalledDM-3200 can be rebooted Stored a snapshotChanged Current project cannot be renamedSpecifications Block diagram Block diagramSpecifications Level diagram Level diagramPage Page DM-3200
Related manuals
Manual 2 pages 325 b Manual 4 pages 61.69 Kb

DM-3200 specifications

The Tascam DM-3200 is a versatile digital mixing console renowned for its professional audio capabilities and comprehensive feature set. Launched as a part of Tascam’s acclaimed DM series, this console has become a favorite among recording engineers and musicians for its flexibility and high-quality sound processing.

One of the standout features of the DM-3200 is its ability to handle both analog and digital audio signals seamlessly. With 32 input channels, it provides ample connectivity options that are vital for modern studios. It supports both analog line-level signals and digital inputs via ADAT, AES/EBU, and S/PDIF, which allows for extensive routing and integration with various devices and systems.

The DM-3200 features an 8-bus architecture, which enables users to create complex mixes with ease. Each channel is equipped with a 4-band parametric EQ, offering precise control over the tonal balance of each audio source. The onboard effects processing includes virtual effects such as reverb, delay, and modulation, which enhances the overall sound quality and provides creative options for mixing and mastering.

Another notable aspect of the DM-3200 is its intuitive user interface. The console features an LCD display alongside faders, knobs, and buttons designed for quick and efficient operation. The layout facilitates smooth navigation through menus, making it user-friendly for both novice and experienced engineers.

In terms of recording and playback, the DM-3200 supports 24-bit/96 kHz audio resolution, ensuring high-fidelity sound for both tracking and mixing. This capability makes it suitable for post-production, live sound, and studio work, providing high-quality audio requisite in various applications.

Tascam has integrated advanced automation features into the DM-3200, allowing users to automate fader positions, effects parameters, and more. This feature is particularly beneficial during mixing sessions where precision and repeatability are essential.

Additionally, the DM-3200 is capable of digital multitrack recording and can interface seamlessly with DAWs via FireWire, enhancing its versatility in a hybrid studio environment. Whether you are recording a band, mixing a podcast, or producing a film score, the Tascam DM-3200 stands out as a powerful tool in professional audio production.