Sennheiser W100 manual Multi-channel operation, Adjusting the sensitivity transmitters only

Page 32

Starting the scan and storing the scan result

Before starting the scan, switch all transmitters of your system off, since channels used by switched-on transmitters will not be displayed as “free channels”.

Select the “SCAN” menu.

Select “START” and confirm your selection by pressing the SET button. After the scan is completed, the number of free channels is displayed. Pressing the SET button once more will store the scan result and lock all channels that are used or subject to interference.

Releasing locked channels

Select the “SCAN” menu.

Select “CLEAR” and confirm your selection by pressing the SET button. All channels in this channel bank can now be selected again.

Multi-channel operation

For multi-channel operation, only use the free channels in a channel bank.

Before putting the transmission links into operation, we recommend perfor- ming an auto scan.

Select a channel bank on a receiver.

Scan this channel bank for free channels. If not enough free channels are available in the selected channel bank, repeat the scan with another chan- nel bank.

Apply the scan result to all other transmitters and receivers.

SENSIT

EM 100 G2

EM 100 G2

EK 100 G2

Adjusting the sensitivity (transmitters only)

Via the “SENSIT” menu, you can adjust the modulation level of the transmit- ters. This changes the transmitter’s input sensitivity.

The input sensitivity is adjusted too high when close talking distances, spea- kers with loud voices or loud music passages cause overmodulation in the transmission link. In this case, the SK 100 G2’s yellow LED (AF PEAK) will light up and the receiver’s level display for audio signal (AF) will show full deflection (see: „Modulation display of the receiving transmitter“ on page 12).

If, on the other hand, the sensitivity is adjusted too low, the transmission link will be undermodulated, which would result in a signal with high background noise.

The sensitivity is correctly adjusted when the level display for audio signal “AF” shows full deflection only during the loudest passages.

Note:

For monitoring the adjusted sensitivity, the transmitter’s level display for audio signal (AF) always indicates the audio level – even if the transmitter is muted.

32

Image 32

Contents 100 Safety instructions Thank you for choosing SennheiserContents Evolution wireless series ew 100 G2 Channel bank systemSystem variants Delivery includes Areas of applicationEM 100 G2 rack-mount receiver Power buttonOverview of operating controls EK 100 G2 bodypack receiver SK 100 G2 bodypack transmitter SKP 100 G2 plug-on transmitter SKM 100 G2 radiomicrophone Operation and battery status indication EK 100 G2 only Transmitter battery status indication EM 100 G2 onlyRF signal indication EK 100 G2 only Indications and displays on the receiversModulation display of the receiving transmitter Pilot displayDiversity display EM 100 G2 only Display backlighting EK 100 G2 onlyOperation and battery status indication Indications and displays on the transmittersModulation display AF peak indication SK 100 G2 onlyConnecting the antennas Connecting the mains unitPreparing the components for use Mounting the receiver feetRack adapter and antenna mount accessories Connecting the amplifier/mixing consoleService interface Bottom sides of the receivers Connecting units to the audio output Inserting and replacing the batteriesConnecting the microphone/line cable Mounting the bodypack receiver to a cameraAttaching the microphones Positioning the microphonesPlugging the plug-on transmitter onto a microphone Changing the microphone head Using the components Switching the components on/offSwitching the rack-mount receiver on/off Switching the bodypack receiver/transmitter on/offActivating/deactivating the lock mode Switching the radiomicrophone on/offMuting the transmitters Muting the SK 100 G2 and SKP 100 G2 transmittersAttaching the components to clothing Attaching the bodypack receiver/transmitter to clothingOverview of menus Operating menuButtons Working with the operating menu Operating menu of the receivers ExitName Exit Operating menu of the transmittersDisply Switching between the channels in a channel bank Adjustment tips for the operating menuSwitching between channel banks Adjusting the sensitivity transmitters only Multi-channel operationStarting the scan and storing the scan result Releasing locked channelsSpecial feature of the SKP 100 G2 plug-on transmitter Adjusting the audio output level receivers onlyAdjusting the squelch threshold receivers only Selecting the standard display Entering a nameLoading the factory-preset default settings Activating/deactivating the pilot tone transmission orPilot tone evaluation Exiting the operating menuIf problems occur Error checklistRecommendations and tips Care and maintenance For multi-channel operationAdditional information HDX noise reductionWireless transmission systems SquelchPilot tone squelch Field strength-dependent squelchDiversity reception Receivers SpecificationsSystem Connector assignment TransmittersMicrophones Microphone headsPage Accessories Warranty regulations Manufacturer declarationsCE Declaration Conformity Batteries or rechargeable batteries