Telex Q II - FOH specifications Declaration of Conformity

Page 3

Declaration of Conformity

The Manufacturer of the Products covered by this Declaration is

Klark Teknik Building, Walter Nash Road, Kidderminster, Worcestershire, DY11 7HJ.

The Directives Covered by this Declaration.

89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC 73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.

The Products Covered by this Declaration.

Equipment type

Product Name

Variants

Audio Mixing Console

Q2

Q2 VCA

Audio Mixing Console

Q2 Monitor

Meterbridge

Audio Mixing Console

QMR

Meterbridge

Audio Mixing Console

FMR

 

Audio Mixing Console

Forum

PA,Matrix,Mute

Audio Mixing Console

Forum Monitor

Meterbridge

Audio Mixing Console

XL200

 

Audio Mixing Console

XL250

 

The Basis on which Conformity is being Declared

The products identified above comply with the protection requirements of the EMC Directive and with the principal elements of the safety objectives of the Low Voltage Directive, and the manufacturer has applied the following standards:

EN 55013 : 1990

Limits and methods of measurement of radio disturbance characteristics of Broadcast Receivers and Associated Equipment. EN 50082-1 : 1992

Electromagnetic Compatibility - Generic Immunity Standard Part 1. Residential, commercial and light industry. EN 60065 : 1994

Safety requirements for mains operated electronic related apparatus for household and similar general use.

The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage Directive has been compiled by the signatory below and is available for inspection by the relevant enforcement authorities. The CE mark was first applied in 1996.

Signed:

................................G.M.Squires

Authority:

Product Support Manager.

Date:

1st, January 1997.

Attention

The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which must be observed when these products are taken into service to maintain compliance with the above directive. Details of these special measures and limitations to use are available on request, and are also contained in product manuals.

Q2 OPERATIONAND MAINTENANCE MANUAL 9601

3

Image 3
Contents II FOH Contents Declaration of Conformity Left Centre Right General InformationQ2 in USE Left Centre Right Effects Matrix Outputs Warranty Q2 Operationand Maintenance Manual Dimensions Distortion SpecificationsMaximum Gain Frequency ResponseQ2 Operationand Maintenance Manual Wiring Considerations Grounding Q2 Operationand Maintenance Manual Do not Disconnect the Mains Earth Cables Module Descriptions CUE Interlock Mode Master CUE Reset Matrix Section 20DB PAD Input Module Equaliser HI MIDLO MID PRE AuxiliariesDIR Routing and Status PAN MonoLCR Meter Mute Group CUEFader SafeInsert Send Connectors and PIN AssignmentsMIC Input Line InputVCA Input Module VCA/MUTE Group 1 Assign EXTExternal VCA Fader Control Wiring Width Phase ReverseStereo Effect Return Module CUTLF EQ HF EQMONO/STEREO BALVCA/MUTE Group Connectors and PIN Assignments Mono Subgroup Output Module Matrix Meter Group MeterCUE/SOLO Matrix Send PRE SUB/LCRConnectors and PIN Assignments Stereo Subgroup Output Module CUE/SOLO BAL Connectors and PIN Assignments LCR Subgroup Output Module Group Meters L, C, R VCA/MUTE Group 1 Assign Connectors and PIN Assignments 1 Level Foldback Master ModuleAUX 1 Level HEADPHONES/HEADSET OutputsHeadphones Level Auxiliary Master ModuleStereo Master Module Groups Internal SINEWAVE/NOISE GeneratorOSC GENERATOR/TALKBACK Assign MatrixDIM Monitor SectionTape Monitor LevelCUE Intlk CUE ResetCUE/SOLO Master Section PFL/AFL TrimComms on Talkback SystemTone LevelFaders Master Output Control PRETo Mono Mono CUE/SOLOMaster Connector Panel VCA Master Module Q2 Operationand Maintenance Manual BAL VCA VCA Master Section CUTConnectors and PIN Assignments Audio Master Module Q2 Technical Description Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Auxiliary Master Module Foldback Master Module Signal Path Reset CircuitSolo System Q2 Operationand Maintenance Manual Q2 Panning ON/CUT Circuit Midi Interface Input Module Resistors Q2 RoutingLevel Meter Input Module Routing LinksInput Module Links Mono Group Output Module Mono Group Output Links Stereo Group Output Links Stereo Group Output ModuleLCR Group Output Links LCR Group Output ModuleInput Module Q2 VCAInput SUB Board Links Adjustments Output ModuleOutput SUB Board Links VCA Master Modules Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual