Telex Q II - FOH specifications Bal

Page 59

BAL

Balances the stereo signal within the stereo bus, or within pairs of groups if the MONO/STEREO button is set to STEREO.

MONO/STEREO

If set to MONO, a mono sum of the stereo signal is fed to any selected group. If set to stereo, a stereo signal is sent to pairs of groups via the BAL control, left to odd, right to even, groups.

MONO

Assigns a MONO sum of the stereo signal to the main MONO (Centre) bus.

L/R

Assigns the stereo signal to the main STEREO L/R bus.

1

Assigns signal to group 1, either as a mono sum, or the left channel, depending on the setting of the mono stereo switch. Similarly for groups 2-8.

ON

Enables the Effect Return signal path.

SAFE

Deselects the return from the VCA/MUTE Group system, without affecting the mute group assignments. Useful to locally protect signals, or manually override grouped MUTE ON conditions.

VCA/MUTE GROUP 1

Assigns the channel to VCA/MUTE Group 1. Similarly for VCA/ MUTE Groups 2 through 8.

CUE

Assigns the stereo signal to the CUE system, with flashing led indication when enabled.

FADER

Controls the level of the EFFECT RETURN section of the module.

Q2 OPERATIONAND MAINTENANCE MANUAL 9601

59

Image 59

Contents II FOH Contents Declaration of Conformity Left Centre Right General InformationQ2 in USE Left Centre Right Effects Matrix Outputs Warranty Q2 Operationand Maintenance Manual Dimensions Distortion SpecificationsMaximum Gain Frequency ResponseQ2 Operationand Maintenance Manual Wiring Considerations Grounding Q2 Operationand Maintenance Manual Do not Disconnect the Mains Earth Cables Module Descriptions CUE Interlock Mode Master CUE Reset Matrix Section 20DB PAD Input Module LO MID EqualiserHI MID PRE AuxiliariesDIR LCR Routing and Status PANMono Meter Mute Group CUEFader SafeInsert Send Connectors and PIN AssignmentsMIC Input Line InputVCA Input Module VCA/MUTE Group 1 Assign EXTExternal VCA Fader Control Wiring Width Phase ReverseStereo Effect Return Module CUTLF EQ HF EQMONO/STEREO BALVCA/MUTE Group Connectors and PIN Assignments Mono Subgroup Output Module CUE/SOLO Matrix MeterGroup Meter Matrix Send PRE SUB/LCRConnectors and PIN Assignments Stereo Subgroup Output Module CUE/SOLO BAL Connectors and PIN Assignments LCR Subgroup Output Module Group Meters L, C, R VCA/MUTE Group 1 Assign Connectors and PIN Assignments 1 Level Foldback Master ModuleAUX 1 Level HEADPHONES/HEADSET OutputsHeadphones Level Auxiliary Master ModuleStereo Master Module Groups Internal SINEWAVE/NOISE GeneratorOSC GENERATOR/TALKBACK Assign MatrixDIM Monitor SectionTape Monitor LevelCUE Intlk CUE ResetCUE/SOLO Master Section PFL/AFL TrimComms on Talkback SystemTone LevelFaders Master Output Control PRETo Mono Mono CUE/SOLOMaster Connector Panel VCA Master Module Q2 Operationand Maintenance Manual BAL VCA VCA Master Section CUTConnectors and PIN Assignments Audio Master Module Q2 Technical Description Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Auxiliary Master Module Foldback Master Module Solo System Signal PathReset Circuit Q2 Operationand Maintenance Manual Q2 Panning ON/CUT Circuit Midi Interface Input Module Resistors Q2 RoutingLevel Meter Input Module Routing LinksInput Module Links Mono Group Output Module Mono Group Output Links Stereo Group Output Links Stereo Group Output ModuleLCR Group Output Links LCR Group Output ModuleInput Module Q2 VCAInput SUB Board Links Output SUB Board Links AdjustmentsOutput Module VCA Master Modules Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual