Telex Q II - FOH specifications Warranty

Page 7

WARRANTY

If within a period of twelve months from the date of delivery of the equipment to the End User it shall prove defective by reason only of faulty materials and/or workmanship (but no faulty design) to such an extent that the effectiveness and/or the usability thereof is materially affected, the Equipment or the faulty component shall be returned to the Distributor or DDA and subject to the following conditions the Distributor or DDA will repair or at its option re- place the defective components. Any components replaced will become the property of DDA.

Any Equipment or component returned will be at the risk of

the End User whilst in transit (both to and from the Distributor or DDA) and postage and/or freight charges must be prepaid.

This Warranty shall only be available if:-

i)The Equipment has been properly installed in accordance with the instructions contained in this manual.

ii)The End User has notified the Distributor or DDA in writing within 14 days of the defect appearing.

iii)No persons other than authorised representatives of DDA or the Distributor have effected any replacement of parts, maintenance adjustments or repairs to the Equipment.

iv)The End User has used the Equipment for such purposes as DDA recommends with only such operating supplies as meet DDA’s specifications or approval and otherwise in all respects in accordance with DDA’s recommendations.

Defects arising as a result of the following are not covered by this Warranty : -

Faulty or negligent handling, chemical or electro-chemical or electrical influences, accidental damage, Acts of God, neglect, defficiency in electrical power, air conditioning or humidity control.

Benefit of this Warranty may not be assigned by the End User.

End Users who are consumers should note that their rights under this Warranty are in addition to and do not affect any other rights to which they may be entitled against the seller of the Equipment.

Q2 OPERATIONAND MAINTENANCE MANUAL 9601

7

Image 7
Contents II FOH Contents Declaration of Conformity Left Centre Right General InformationQ2 in USE Left Centre Right Effects Matrix Outputs Warranty Q2 Operationand Maintenance Manual Dimensions Distortion SpecificationsMaximum Gain Frequency ResponseQ2 Operationand Maintenance Manual Wiring Considerations Grounding Q2 Operationand Maintenance Manual Do not Disconnect the Mains Earth Cables Module Descriptions CUE Interlock Mode Master CUE Reset Matrix Section 20DB PAD Input Module HI MID EqualiserLO MID PRE AuxiliariesDIR Mono Routing and Status PANLCR Meter Mute Group CUEFader SafeInsert Send Connectors and PIN AssignmentsMIC Input Line InputVCA Input Module VCA/MUTE Group 1 Assign EXTExternal VCA Fader Control Wiring Width Phase ReverseStereo Effect Return Module CUTLF EQ HF EQMONO/STEREO BALVCA/MUTE Group Connectors and PIN Assignments Mono Subgroup Output Module Group Meter Matrix MeterCUE/SOLO Matrix Send PRE SUB/LCRConnectors and PIN Assignments Stereo Subgroup Output Module CUE/SOLO BAL Connectors and PIN Assignments LCR Subgroup Output Module Group Meters L, C, R VCA/MUTE Group 1 Assign Connectors and PIN Assignments 1 Level Foldback Master ModuleAUX 1 Level HEADPHONES/HEADSET OutputsHeadphones Level Auxiliary Master ModuleStereo Master Module Groups Internal SINEWAVE/NOISE GeneratorOSC GENERATOR/TALKBACK Assign MatrixDIM Monitor SectionTape Monitor LevelCUE Intlk CUE ResetCUE/SOLO Master Section PFL/AFL TrimComms on Talkback SystemTone LevelFaders Master Output Control PRETo Mono Mono CUE/SOLOMaster Connector Panel VCA Master Module Q2 Operationand Maintenance Manual BAL VCA VCA Master Section CUTConnectors and PIN Assignments Audio Master Module Q2 Technical Description Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Auxiliary Master Module Foldback Master Module Reset Circuit Signal PathSolo System Q2 Operationand Maintenance Manual Q2 Panning ON/CUT Circuit Midi Interface Input Module Resistors Q2 RoutingLevel Meter Input Module Routing LinksInput Module Links Mono Group Output Module Mono Group Output Links Stereo Group Output Links Stereo Group Output ModuleLCR Group Output Links LCR Group Output ModuleInput Module Q2 VCAInput SUB Board Links Output Module AdjustmentsOutput SUB Board Links VCA Master Modules Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual