Telex Q II - FOH specifications Cue, Fader, Safe, Mute Group

Page 26

CUE

The CUE (or SOLO) button feeds a Pre-fader or post-fader signal (as selected on the master module PFL or AFL) to the Monitor section (loudspeakers or headphones), replacing the selected monitor source if one is selected. The main stereo output of the console is not affected unless SIP (Solo-in-place) mode has been selected on the master. The yellow led in the CUE switch will flash when the CUE function is active. CUE signals from different sources that are active simultaneously in the non-interlocked mode will be summed.

To latch the CUE function, press the button quickly and release. To unlatch, repeat. To CUE a signal momentarily, hold down the CUE button for at least 1 second. On release, the CUE will also be released.

See THE CUE/SOLO SYSTEM on page 16 for full functional details.

FADER

The fader is the main signal level control for the channel, and is a long-throw type which gives smooth control of the channel level.

SAFE

Deselects the return from the VCA/MUTE Group system, without affecting the mute group assignments. Useful to locally protect signals, or manually override grouped MUTE ON conditions.

MUTE GROUP 1

Assigns the channel to MUTE Group 1. Similarly for MUTE Groups 2 through 8.

Q2 OPERATIONAND MAINTENANCE MANUAL 9601

26

Image 26

Contents II FOH Contents Declaration of Conformity General Information Left Centre RightQ2 in USE Left Centre Right Effects Matrix Outputs Warranty Q2 Operationand Maintenance Manual Dimensions Frequency Response SpecificationsMaximum Gain DistortionQ2 Operationand Maintenance Manual Wiring Considerations Grounding Q2 Operationand Maintenance Manual Do not Disconnect the Mains Earth Cables Module Descriptions CUE Interlock Mode Master CUE Reset Matrix Section 20DB PAD Input Module LO MID EqualiserHI MID Auxiliaries PREDIR LCR Routing and Status PANMono Meter Safe CUEFader Mute GroupLine Input Connectors and PIN AssignmentsMIC Input Insert SendVCA Input Module EXT VCA/MUTE Group 1 AssignExternal VCA Fader Control Wiring CUT Phase ReverseStereo Effect Return Module WidthHF EQ LF EQBAL MONO/STEREOVCA/MUTE Group Connectors and PIN Assignments Mono Subgroup Output Module CUE/SOLO Matrix MeterGroup Meter SUB/LCR Matrix Send PREConnectors and PIN Assignments Stereo Subgroup Output Module CUE/SOLO BAL Connectors and PIN Assignments LCR Subgroup Output Module Group Meters L, C, R VCA/MUTE Group 1 Assign Connectors and PIN Assignments Foldback Master Module 1 LevelAuxiliary Master Module HEADPHONES/HEADSET OutputsHeadphones Level AUX 1 LevelStereo Master Module GENERATOR/TALKBACK Assign Matrix Internal SINEWAVE/NOISE GeneratorOSC GroupsMonitor Level Monitor SectionTape DIMTrim CUE ResetCUE/SOLO Master Section PFL/AFL CUE IntlkLevel Talkback SystemTone Comms onMono CUE/SOLO Master Output Control PRETo Mono FadersMaster Connector Panel VCA Master Module Q2 Operationand Maintenance Manual BAL VCA Master Section CUT VCAConnectors and PIN Assignments Audio Master Module Q2 Technical Description Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual Auxiliary Master Module Foldback Master Module Solo System Signal PathReset Circuit Q2 Operationand Maintenance Manual Q2 Panning ON/CUT Circuit Midi Interface Q2 Routing Input Module ResistorsInput Module Routing Links Level MeterInput Module Links Mono Group Output Module Mono Group Output Links Stereo Group Output Module Stereo Group Output LinksLCR Group Output Module LCR Group Output LinksQ2 VCA Input ModuleInput SUB Board Links Output SUB Board Links AdjustmentsOutput Module VCA Master Modules Q2 Operationand Maintenance Manual Q2 Operationand Maintenance Manual