Bosch Appliances V1.0 Multi Channel DSP Amplifier, Logic inputs, 8CS and WCP RS485

Page 47

PLENA matrixTechnical Data en 47

Logic inputs

Connector	2‑pole Phoenix terminal (metric)


8CS and WCP (RS485)

Call station connector	1x	RJ45

Wall control panel connector	1x	RJ45


Amplifier	2x

Connector	RJ45

Nominal level	1 V

Impedance	<100 ohm


Ethernet (10/100 Mbit/s)	1x

Connector	RJ45

Notice!

Maximum load means maximum two multi-channel amplifiers, call stations and wall control panels connected.

11.1.2Multi Channel DSP Amplifier

	Power supply

	Mains voltage:

	–	Nominal input voltage	100 - 240 VAC ±10%, 50/60 Hz

	–	Input voltage limits	90 - 264 VAC

	Power consumption (-6dB/idle/standby):

	–	PLM‑4P125	254 W / 27 W / 6 W

	–	PLM‑4P220	412 W / 36 W / 6 W


	Performance

	Rated outputs voltage/impedance		100 V / 70 V / 8 ohm / 4 ohm

	Rated output power per channel (continous *):

	–	PLM‑4P125	130 W

	–	PLM‑4P220	220 W

	Rated output power per channel (burst *):

Bosch Security Systems B.V.

Operation manual

2013-06 V1.0

Image 47

Contents Plena matrix Page Table of contents Technical Data TroubleshootingMaintenance Business Equipment For commercial or professional use 1SafetySafety precautions 1FCC and IcesEn Safety Plena matrix About this manual Release date Documentation version Reason Document historyPLM-4P125 and PLM‑4P220 Multi channel DSP Amplifiers 3System overviewPLM‑WCP Wall Control Panel PC Configuration and User GUIPLM‑8CS 8 Zone Call Station Plena matrix System overview en 4Planning DSP Matrix Mixer and Amplifiers 5InstallationCall Station 3Wall Control Panel Refer to Wall Control Panel DIP switch settings,See also PC GUI application software installationPC GUI software PC requirements5iOS GUI software Description ConnectionsWall Control Panel Number Description Multi channel DSP AmplifierNumber Description Panels 4DSP Matrix MixerDo not connect any device, other than a PLM‑4Px2x amplifier DSP Matrix Mixer and Amplifiers, Call station ID numbers DIP switch 7ConfigurationCall Station DIP switch settings Wall Control Panel DIP switch settings 3Multi Channel DSP Amplifier settings Proceed as follows 4DSP matrix mixer PC GUIDSP matrix mixer GUI main screen DSP matrix mixer PC GUI control functions UserMulti Channel DSP Amplifier PC GUI DSP setupOther DSP matrix mixer configurations in the GUI Plena matrix Configuration en Amplifier GUI main screen Amplifier Bridging Configuration Continue with one of the following chapters 8Operation1Start Continue with 2Call StationMaking an announcement Pre-settings and selectionsTop LED 0dB attenuation Select the input source Adjust the audio output volume levelWith DSP / PC GUI functionality Standalone without connection to the PC GUI3Operate the amplifier with the PC GUI Activate the active override audio input functionActivate the amplifier auto standby RS485 LED 5DSP Matrix Mixer3Operating the DSP Matrix Mixer/system with the GUI 1Activate the override input functionActivate the Alert/EVAC override function Problem Possible cause Possible solution DSP matrix mixer or TroubleshootingCall stations / Wall Control Problem Possible cause Possible solutionCall station’s microphone 1Customer service 10.3 Check the connectors and grounding Maintenance10.1 Clean the units 10.2 Clean air ventsDSP Matrix Mixer Technical Data11.1 Electrical Amplifier Multi Channel DSP AmplifierLogic inputs 8CS and WCP RS485Connectors 11.1.4 Wall Control Panel Call Station11.2.3 Call Station 11.2 Mechanical11.2.1 DSP Matrix Mixer 11.2.4 Wall Control Panel 11.3.3 Call Station 11.3 Environmental conditionsStandards 11.3.1 DSP Matrix MixerPage Bosch Security Systems B.V