Bosch Appliances V1.0 operation manual 7Configuration, Call Station DIP switch settings

Page 23

PLENA matrix	Configuration en 23

7Configuration

Call Station DIP switch settings, page 23

Wall Control Panel DIP switch settings, page 24

Multi Channel DSP Amplifier settings, page 25

DSP matrix mixer PC GUI, page 26

Multi Channel DSP Amplifier PC GUI, page 28

7.1	Call Station
	Configuration of zone groups, printable labels for the call stations and chimes is done via the
	PC software GUI. Refer to DSP matrix mixer PC GUI, page 26.
7.1.1	Call Station DIP switch settings
	DIP switches are use to set individual ID numbers to the call stations. This is so it can be
	recognized by the DSP matrix mixer in the system. Each connected call station must have its
	own individual ID assigned.
	1.	To set the call-station ID use the 3‑way DIP switch on the base of the unit:
		– Factory default ID setting: call station 1 (all switches are OFF).

						Call station ID numbers

	DIP switch		1*	2	3		4	5	6	7	8

	1		OFF	ON	OFF		ON	OFF	ON	OFF	ON

	2		OFF	OFF	ON		ON	OFF	OFF	ON	ON

	3		OFF	OFF	OFF		OFF	ON	ON	ON	ON

* Factory default.

Notice!

A DIP switch in the down position is OFF.

A DIP switch in the up position is ON.

Eg. Down – Up - Down will equal call station ID number 3 in the table above.

Bosch Security Systems B.V.

Operation manual

2013-06 V1.0

Image 23

Contents Plena matrix Page Table of contents Technical Data TroubleshootingMaintenance Business Equipment For commercial or professional use 1SafetySafety precautions 1FCC and IcesEn Safety Plena matrix About this manual Release date Documentation version Reason Document historyPLM-4P125 and PLM‑4P220 Multi channel DSP Amplifiers 3System overviewPLM‑WCP Wall Control Panel PC Configuration and User GUIPLM‑8CS 8 Zone Call Station Plena matrix System overview en 4Planning DSP Matrix Mixer and Amplifiers 5InstallationCall Station 3Wall Control Panel Refer to Wall Control Panel DIP switch settings,See also PC GUI application software installationPC GUI software PC requirements5iOS GUI software Description ConnectionsWall Control Panel Number Description Multi channel DSP AmplifierNumber Description Panels 4DSP Matrix MixerDo not connect any device, other than a PLM‑4Px2x amplifier DSP Matrix Mixer and Amplifiers, Call station ID numbers DIP switch 7ConfigurationCall Station DIP switch settings Wall Control Panel DIP switch settings 3Multi Channel DSP Amplifier settings Proceed as follows 4DSP matrix mixer PC GUIDSP matrix mixer GUI main screen DSP matrix mixer PC GUI control functions UserMulti Channel DSP Amplifier PC GUI DSP setupOther DSP matrix mixer configurations in the GUI Plena matrix Configuration en Amplifier GUI main screen Amplifier Bridging Configuration Continue with one of the following chapters 8Operation1Start Continue with 2Call StationMaking an announcement Pre-settings and selectionsTop LED 0dB attenuation Select the input source Adjust the audio output volume levelWith DSP / PC GUI functionality Standalone without connection to the PC GUI3Operate the amplifier with the PC GUI Activate the active override audio input functionActivate the amplifier auto standby RS485 LED 5DSP Matrix Mixer3Operating the DSP Matrix Mixer/system with the GUI 1Activate the override input functionActivate the Alert/EVAC override function Problem Possible cause Possible solution DSP matrix mixer or TroubleshootingCall stations / Wall Control Problem Possible cause Possible solutionCall station’s microphone 1Customer service 10.3 Check the connectors and grounding Maintenance10.1 Clean the units 10.2 Clean air ventsDSP Matrix Mixer Technical Data11.1 Electrical Amplifier Multi Channel DSP AmplifierLogic inputs 8CS and WCP RS485Connectors 11.1.4 Wall Control Panel Call Station11.2.3 Call Station 11.2 Mechanical11.2.1 DSP Matrix Mixer 11.2.4 Wall Control Panel 11.3.3 Call Station 11.3 Environmental conditionsStandards 11.3.1 DSP Matrix MixerPage Bosch Security Systems B.V