Zenoah EDG2300R manual Avoid Noise Problem

Page 14

English

4. For safe operation

engine, hold it firmly in place so as to ensure that nor the throttle may not come into contact with any obstacles when the engine starts up.

Never place the throttle into the high speed position when starting the engine.

After starting up the engine, check to make sure that the drills stop rotating when the throttle is moved fully back to its original position. If the drills continue to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Red Max servicing dealer for repair.

AVOID NOISE PROBLEM

NOTE

Check and follow the local regulations as to sound level and hours of operations for portable gas drill.

In general, operate portable gas drill between 8a.m.and 5p.m.on week days and 9a.m.to 5p.m.weekends. Avoid using portable gas drill late at night and/or early in the morning.

THINGS TO BE CAREFUL ABOUT WHEN USING YOUR PORTABLE GAS DRILL

When using your portable gas drill, grip the handles of the portable gas drill firmly with both hands, place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working.

Maintain the speed of the engine at the level required to perform drilling work, and never raise the speed of the engine above the level necessary.

Always be sure never to allow other persons to come within the work area while drilling.

Be especially careful not to slip if it is raining or if rain has just stopped, as the ground is likely to be slippery at such times.

If the grass or other object gets caught in the drill during operation, always be sure to turn off the engine before removing the object.

Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Establish a safe method for gaining your attention during operation. Be careful if you are approached.

If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around.

14

Image 14
Contents EDG2300R Contents Tables des matieres Contenido EDG2300R SpecificationsParts location Especificaciohes Emplacement des pieces Situación de las piezasFiche technique Position Symbols on the machineImportant Engine Information Emission ControlControl DE Emisiones EmplacementPosición For safe operation Consignes de securite Instrucciones de seguridad Work Gear and Clothing Avertissement Concernant Manipulation DE Carburant Consignes de securite Instrucciones de seguridadEquipement ET Vêtements DE Travail Equipo Y Prendas DE TrabajoThings to Check Before Using Your Portable GAS Drill Things to Check Before Starting UP the EngineVerifications a Effectuer Avant DE Demarrer LE Moteur Avoid Noise Problem Evitar Problemas DE Ruido Eviter LES Nuisances SonoresPortable GAS Drill Consignes de securite Instrucciones de seguridad Front grip Chuck unit Set upSE1 SE2 SE3 Chuck handle Selection of a Suitable BitLevier du mandrin Sélection d’un trépan approprié Assemblage MontajeAgarradera Levier Palanquita del portabrocaRecommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel Avertissement Advertencia Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation Fonctionnement Uso Stopping Engine How to operate Reverse control OP8OP5 OP6 OP7 OP8 RUN Stop Boring Operation OP6, OP7Marche Comment opérer la commande inverseFonctionnement Uso Levier Cómo operar el control de ReversiónWhen Install or Loosen the Chuck More Securely OP10,11 Adjustment of Idling SpeedIdle adjustment screw OP9 OP10 OP11Tornillo de ajuste de ralentí Vis de réglage du ralentiClé de 19 mm Levier de verrouillage Llave fija de 19 mm Palanca de bloqueoMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoInspection Every 25 Hours MA1 MA2Daily Inspection MA3Entretien Mantenimiento Disposal Cleaning the cylinder finsStorage Nettoyage des ailettes du cylindre Rangement AlmacenamientoMise au rebut Eliminación Limpieza de las aletas del cilindroGuide de localisation des pannes Troubleshooting guide11. Guía de localización y solución de problemas EDG2300R NotaParts list Gear Case a Engine Unit EDG2300R S/N 60000101 and up Qty Key# Part Number Description Limited Warranty There are no Other Express WarrantiesGarantie limitée Garantía Limitada No Existen Otras Garantías ExpresasPage Zenoah AMERICA, INC