Rangemaster U109600-02 manual Fitting the splash back, Fitting a stability bracket, Gas Connection

Page 31

Fitting the splash back

The cooker can be installed with or without the supplied splashback. To fit splash remove the two fixing screws (3mm hexagonal socket head) and nuts that pass through the top of the rear flue grille. Hold the splash back in position. From the rear refit the 2 fixing screws and nuts.

Fitting a stability bracket

A stability bracket or chain (not supplied by with the cooker) should be fitted when the cooker is connected to a flexible gas supply.

When fitting a stability bracket read these instructions together with the leaflet supplied with the bracket.

1.Place the cooker in its intended position and level the cooker.

2.Draw a pencil line 100mm from the front edge of the levelling feet.

3.Mark the centre line for the bracket by measuring 550mm from the left hand side of the cooker.

Gas Connection

The Gas supply needs to terminate with a down facing bayonet. The rear cover boxes limit the position of the supply point.

4.Lower the front roller and move the cooker forward.

5.Measure back from the pencil line 550mm to locate the front edge of the bracket. Fix the bracket to the floor.

6.Measure the height from floor level to engagement edge in back of cooker. Add 3mm to this dimension and assemble the stability bracket to this height. (i.e. from floor level to underside of the top member) and ensure the bracket does not foul the oven burner assembly.

view from the rear

A - position for gas supply connector, B - appliance gas inlet

Because the height of the cooker can be adjusted and each connection is different it is difficult to give precise dimensions. Ideally the house supply bayonet should be in the shaded area shown in the diagram. Although a 900mm hose can be used, a 1250mm hose will allow slightly more flexibility in the positioning of the bayonet and make moving the cooker easier. The hose should be fitted so that both inlet and outlet connections are vertical so that the hose hangs downwards.

The connector is located just below the hotplate level at the rear of the cooker.

For Natural Gas the fl exible hose must be in accordance with B.S.669.

For LP Gas it should be capable of 50mbar pressure, 70°C temperature rise and carry a red stripe, band or label.

If in doubt contact, your supplier.

Screw connect the threaded end of the hose into the gas inlet in the underside of the connector block on the back of the cooker.

After completing the gas connection, check the cooker is gas sound with a pressure test.

Pressure testing

The gas pressure can be measured at one of the centre hotplate burner injectors (not the Wok burners). Lift off a burner head. Fit the pressure gauge to the injector. Turn on the hotplate burner and turn on and light one of the other hotplate burners.

For Natural Gas cookers the pressure should be 20mbar.

For LP Gas cookers the pressure should be 29mbar for Butane

37mbar for Propane.

Reassemble burner top, making sure it is reassembled in the correct way on the burner body.

31

Image 31
Contents Dual Fuel Gas and Electricity on InstallationThis appliance should not be installed in a boat or caravan Be safeContents Hotplate Burners High/medium GriddleMedium/low Wok cradle Care and CleaningEssential information Never close the grill door when the grill is on Using the grillGlide-out Grill Left Hand Oven Right Hand Fan Oven OvensTo time something that’s cooking minute minder Setting the time of dayTo stop the beeper when it sounds ClockTo activate the key lock Auto is showing, you want to reset to manual cookingClock Special Features Key Lock To start & stop the oven automaticallyBoth Ovens Cooking using the timerMulti-function oven functions Multi-function ovenConventional oven top and base heat HandyrackOven light Oven shelvesStorage Food Cooking chart Fan assisted oven functionMulti-function Oven cooking guide Ensure meat and poultry is fully cooked before servingFish Oven Cooking chart Conventional and full Fan oven functionsWok burners Cleaning your cookerHotplate burners Central hotplateGlide-out Grill GriddleOven and Grill Cleaning Table HotplatePart Finish Recommended Cleaning Method Outside of cookerDo not put the side runners in a dishwasher Control Panel and DoorsOvens Removing the Oven LiningsTo refit the draw Moving your cookerTroubleshooting Oven light is not working Oven temperature getting hotter as the cooker gets olderHotplate ignition or hotplate burners faulty Grill not cooking properly0800 111 General Safety InstructionsThis appliance is heavy, take care when moving it Location of Cooker InstallationDear Installer Provision of VentilationYou will also need the following tools Checking the partsUnpacking the Cooker Positioning the CookerMoving the Cooker Fit the Handles LevellingHandles should be above the fixings Gas Connection Pressure testingFitting the splash back Fitting a stability bracketFitting the plinth Electrical ConnectionGrill Oven checkStick on label Tap adjustmentConversion to LP gas JetsServicing Notes To Change a Hotplate Tap To Remove a ThermostatTo Remove or Change a Hotplate Burner To Change Grill ControllerTo Change Oven Door Seal To Adjust Oven Door Catch KeepTo Change Oven Door Outer Panel To Change Oven Door CatchTo Remove Grill Element To Replace an Oven FanTo Remove the left hand Oven Bottom and Top Elements To Remove an Oven fan ElementCircuit Diagram Connections Technical DataDimensions This cooker is category II2H3+