Rangemaster U109600-02 manual To Replace an Oven Fan, To Remove an Oven fan Element

Page 37

SERVICING - WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Remove the fixings that secure the inner back to the oven rear.

Lift the removable panel away. Re-assemble in reverse order. Ensure that the retaining fixings are fully tightened. For the left hand oven unscrew the 2 thermostat phial fixing screws. Remove the screws that secure the inner back to the oven rear. Lift the removable panel away. Re-assemble in reverse order. Ensure that the retaining fixings are fully tightened.

22. To Replace an Oven Fan

Disconnect from electricity supply.

Pull the unit forward to access the cover boxes at the rear of the appliance. Remove the fixings that secure the cover and lift it clear. Remove the fan wiring, noting the connection positions. Remove the inner back as detailed in Section

20.Hold the fan blades and undo the centre nut (left hand thread), brass washers, fan blade and Circlip. Undo the fixings that retain the fan and remove it from the cavity rear. Fit the replacement and re-assemble parts in reverse order. Check that the oven operates satisfactorily.

25. To Remove the left hand Oven Bottom and Top Elements

Disconnect from the electricity supply.

Bottom Element

Pull the cooker forward to access the cover boxes at the rear of the unit. Remove the fixings that secure the cover and lift it clear.

Remove the 2 screws ‘A’ and allow the plate to drop down.

23. To Remove an Oven fan Element

Disconnect from electricity supply.

Remove the inner back as detailed in Section 20. Remove the fixings that secure the element within the oven and lift the element away carefully.

Disconnect the leads and connect to the replacement element and re-assemble parts in reverse order. Check that the oven operates correctly.

24. To Remove Grill Element.

Disconnect from electricity supply.

Remove grill pan from grill chamber. From inside grill compartment remove enamelled front shield from grill roof, 2 screws and washers. Remove 2 screws and washers securing the grill element front support. Remove 1 screw from each of the grill elements and withdraw grill elements from grill chamber. Disconnect the leads and connect to the replacement elements and re-assemble parts in reverse order. Check operation of grill.

Remove the 2 screws B, holding the element to the bottom sheet.

Disconnect the leads, noting their positions.

Withdraw bottom element. Fit the new element and re- assemble parts in reverse order.

Top Element

Open the left hand oven door and undo the fixings that secure the heat shield. Remove the top element bracket fixings and withdraw element. Replace the element and re-assemble parts in reverse order. Check that the oven operates satisfactorily.

26. To change oven light bulb.

Disconnect from the electricity supply. Remove the oven furniture. Unscrew the bulb.

Fit an Edison screw fitting 15W 125-130V lamp, FOR OVENS. It must be a special bulb, heat resistant to 300 °C.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Dual Fuel This appliance should not be installed in a boat or caravan InstallationBe safe Gas and Electricity onContents Hotplate Burners High/medium GriddleMedium/low Wok cradle Care and CleaningEssential information Never close the grill door when the grill is on Using the grillGlide-out Grill Left Hand Oven Right Hand Fan Oven OvensTo stop the beeper when it sounds Setting the time of dayClock To time something that’s cooking minute minderClock Special Features Key Lock Auto is showing, you want to reset to manual cookingTo start & stop the oven automatically To activate the key lockBoth Ovens Cooking using the timerMulti-function oven functions Multi-function ovenConventional oven top and base heat HandyrackOven light Oven shelvesStorage Multi-function Oven cooking guide Cooking chart Fan assisted oven functionEnsure meat and poultry is fully cooked before serving FoodFish Oven Cooking chart Conventional and full Fan oven functionsHotplate burners Cleaning your cookerCentral hotplate Wok burnersGlide-out Grill GriddlePart Finish Recommended Cleaning Method Cleaning Table HotplateOutside of cooker Oven and GrillOvens Control Panel and DoorsRemoving the Oven Linings Do not put the side runners in a dishwasherTo refit the draw Moving your cookerTroubleshooting Hotplate ignition or hotplate burners faulty Oven temperature getting hotter as the cooker gets olderGrill not cooking properly Oven light is not working0800 111 General Safety InstructionsThis appliance is heavy, take care when moving it Dear Installer InstallationProvision of Ventilation Location of CookerYou will also need the following tools Checking the partsUnpacking the Cooker Positioning the CookerMoving the Cooker Fit the Handles LevellingHandles should be above the fixings Fitting the splash back Pressure testingFitting a stability bracket Gas ConnectionGrill Electrical ConnectionOven check Fitting the plinthConversion to LP gas Tap adjustmentJets Stick on labelServicing Notes To Remove or Change a Hotplate Burner To Remove a ThermostatTo Change Grill Controller To Change a Hotplate TapTo Change Oven Door Outer Panel To Adjust Oven Door Catch KeepTo Change Oven Door Catch To Change Oven Door SealTo Remove the left hand Oven Bottom and Top Elements To Replace an Oven FanTo Remove an Oven fan Element To Remove Grill ElementCircuit Diagram Dimensions Technical DataThis cooker is category II2H3+ Connections
Top Page Image Contents