Rangemaster U109600-02 manual Conversion to LP gas, Jets, Stick on label, Tap adjustment

Page 33

SERVICING - WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Conversion to LP gas

Check in the Technical Data section at the back of the book that the cooker is convertible to the gas you want to use.

This conversion must be performed by a competent person. After conversion the installation must comply with the relevant regulations and also the local electricity supply company requirements. Read the instructions before converting this appliance.

Failure to convert the appliance correctly could invalidate any warranty or liability claims and lead to prosecution.

This instruction must be used in conjunction with the rest of the appliance instruction, in particular for information on Standards, cooker positioning, connection hose suitability etc.

Open the oven door & or grill door and remove the fixing screws underneath the control panel. NB some models have a plate under the facia held in place by the bottom fixing screws.

Lower facia panel clear of top retaining tags.

A tap bypass screw

Turn the bypass screw on each gas control clockwise to the stop.

When servicing or replacing gas-carrying components disconnect from gas before commencing operation and check appliance is gas sound after completion.

Do not use re-conditioned or unauthorised gas controls.

Jets

Standard burner

Wok burner

A jet, B internal injector, C external injector

Remove burner caps and heads. Remove old jets. Fit new jets (see Technical Data section at the back of the book for correct jets). Reassemble in reverse order.

Stick on label

Stick the appropriate label on to the data badge to indicate the gas the appliance is now set for.

Pressure Testing

Connect the appliance to the gas supply. Check the appliance is gas sound.

The gas pressure can be measured at one of the left hand hotplate burner jets. Lift off a burner head. Fit the pressure gauge to the jet. Turn on the hotplate burner and turn on and light one of the other burners.

Reassemble burner top, making sure it is reassembled in the correct way on the burner body.

Check the appliance is gas sound. Check operation of all the burners.

Tap adjustment

Pull off all the control knobs. If the hand rail has been fitted remove it - remove the plastic blanking plugs and remove the 2 end bracket fixing screws.

Remove the 2 cross headed screws that were hidden by the hand rail end brackets.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Dual Fuel This appliance should not be installed in a boat or caravan InstallationBe safe Gas and Electricity onContents Hotplate Burners Griddle High/mediumMedium/low Care and Cleaning Wok cradleEssential information Using the grill Never close the grill door when the grill is onGlide-out Grill Left Hand Oven Right Hand Fan Oven OvensTo stop the beeper when it sounds Setting the time of dayClock To time something that’s cooking minute minderClock Special Features Key Lock Auto is showing, you want to reset to manual cookingTo start & stop the oven automatically To activate the key lockBoth Ovens Cooking using the timerMulti-function oven functions Multi-function ovenConventional oven top and base heat HandyrackOven light Oven shelvesStorage Multi-function Oven cooking guide Cooking chart Fan assisted oven functionEnsure meat and poultry is fully cooked before serving FoodFish Oven Cooking chart Conventional and full Fan oven functionsHotplate burners Cleaning your cookerCentral hotplate Wok burnersGlide-out Grill GriddlePart Finish Recommended Cleaning Method Cleaning Table HotplateOutside of cooker Oven and GrillOvens Control Panel and DoorsRemoving the Oven Linings Do not put the side runners in a dishwasherTo refit the draw Moving your cookerTroubleshooting Hotplate ignition or hotplate burners faulty Oven temperature getting hotter as the cooker gets olderGrill not cooking properly Oven light is not working0800 111 General Safety InstructionsThis appliance is heavy, take care when moving it Dear Installer InstallationProvision of Ventilation Location of CookerYou will also need the following tools Checking the partsPositioning the Cooker Unpacking the CookerMoving the Cooker Levelling Fit the HandlesHandles should be above the fixings Fitting the splash back Pressure testingFitting a stability bracket Gas ConnectionGrill Electrical ConnectionOven check Fitting the plinthConversion to LP gas Tap adjustmentJets Stick on labelServicing Notes To Remove or Change a Hotplate Burner To Remove a ThermostatTo Change Grill Controller To Change a Hotplate TapTo Change Oven Door Outer Panel To Adjust Oven Door Catch KeepTo Change Oven Door Catch To Change Oven Door SealTo Remove the left hand Oven Bottom and Top Elements To Replace an Oven FanTo Remove an Oven fan Element To Remove Grill ElementCircuit Diagram Dimensions Technical DataThis cooker is category II2H3+ Connections
Top Page Image Contents