Kenmore 148.1615421 manual Grill Head Assembly

Page 18

Attach the drip tray support to the beam and rear panel with four 3/16-24 x 3/8 in. screws as shown. Note: Tabs at front attach beneath beam upper ledge.

Drip tray support

Left Panel

Rear Panel	3/16-24 x 3/8 in. Screw
Rear Panel	Qty. 4
	Right Panel

Beam

Grill Head Assembly

First, lock the two rear casters of the grill cart.

Locate the gas pressure regulator and igniter wires under the grill head control panel. Carefully cut the tie wrap(s) from the regulator hose. With the aid of an assistant, lift and place the grill head onto the cart, making sure that the regulator hose and igniter wires hang down into the cart. Align the corner holes at the base of the grill head with the holes in the corner tabs of the cart. Attach the grill head to the cart with four 3/16-24 x 3/8 in. screws.

WARNING: Do not lift grill head from sides. Grasp the grill head by the front control panel and rear panel to avoid pinching fingers when lowering grill head onto cart.

3/16-24 x 3/8 in. Screw Qty. 4

18

Image 18

Contents Kenmore Models/Modelos Item / ArtículoInstallation Safety Precautions Call Grill Service Center For Help And PartsSafety Symbols Date PurchasedTable of Contents WarrantyLP Liquefied Petroleum Gas USE and CareLP Tank Removal, Transport and Storage LP Cylinder FillingLP Tank Exchange Connecting Regulator To The LP TankFor your safety LP Tank Leak TestLeak Testing Valves, Hose and Regulator Turn all grill control knobs to OFFFor Safe Use of Your Grill and to Avoid Serious Injury Burner Flame Check Turn controls and gas source or tank OFF when not in useGeneral Grill Cleaning Turning Grill OffCorrect burner-to-valve engagement Cleaning the Burner AssemblyStoring Your Grill Turn gas off at control knobs and LP cylinderIndirect Cooking How To Tell If Meat Is Grilled ThoroughlyFood Safety Burner CookingTo disconnect Natural Gas Connection PreparationOperating Instructions Gas Requirements LP GasHelpful Care and Maintenance Hints Natural GasExcess Flow Control and Low Heat Parts List Key Qty Description ManufacturerParts Diagram Unpacking Rear Panel Beam Right Panel Grill Head Assembly Ground Wire Install the doors Install Wing Tables Wing Table Operation LP Tank Installation Conversion Instructions for Main Burner Conversion Natural Gas Hose Connection Adjust valve control screw Problem Possible Cause Corrective ActionLow heat is found in natural Fecha de compra Símbolos de seguridadPrecauciones de seguridad para la instalación Índice GarantíaUSO Y Cuidado Nunca llene un cilindro a más del 80% de su capacidadCómo conectar el regulador al tanque de LP Intercambio del tanque LPPrueba de fuga del tanque LP Para su seguridadVálvulas para prueba de fugas, manguera y regulador NotaConsejos prácticos sobre seguridad Cómo apagar la parrilla Encendido con fósforosRevisión de la llama del quemador Revisión del encendedorEnganche correcto quemador-válvula Limpieza del ensamble del quemadorAlmacenaje de la parrilla Cocción indirectaCocción con 1 quemador Seguridad alimentariaCómo saber si la carne está totalmente asada Instrucciones para cocción indirectaManguera de extensión de 3,70 m de 3/8 de diámetro interior Preparación de la conexión para gas naturalInstrucciones de funcionamiento Para desconectarGas natural Consejos útiles de cuidado y mantenimientoLista DE Piezas Diagrama DE LAS Piezas Desembalaje Tornillo de 3/16-24 x 3/8 Cant.6 Barra frontal Panel derecho Ensamble de la parte principal de la parrilla Conductor de puesta a tierra Instale las puertasInstalación de las mesas laterales Funcionamiento de la mesa lateral Instalación del tanque de GLP Page Conexión de la manguera para gas natural Ajuste el tornillo de control de la válvula Problema Causa posible Acción correctivaProblema Causa posible Acción correctiva HI Alto