Invacare Pronto M51 Base manual Engaging/Disengaging Motor Release Lever

Page 49

SECTION 8—TOP SHROUD AND WHEELS

Engaging/Disengaging Motor Release Lever

WARNING

DO NOT engage or disengage the motor release lever until the On/Off switch on the joystick is in the Off position.

CAUTION

Ensure both motor release levers are fully engaged before driving the wheelchair

NOTE: For this procedure, refer to FIGURE 8.2.

NOTE: The motor lock disengagement/engagement allows freewheeling or joystick controlled operation. Freewheeling allows an attendant to maneuver the wheelchair without power.

1.Locate the motor release handles on the motors protruding through the top shroud on the rear of the wheelchair.

2.Perform one of the following:

To Disengage the Motor Release Levers ‐ Pull the motor lock lever towards the rear of the wheelchair (freewheel position).

NOTE: This allows the chair to freewheel for pushing, if necessary.

NOTE: It may be necessary to rock the wheels slightly until the motor release lever disengages.

To Engage the Motor Release Levers ‐ Push the motor lock handles towards the front of the wheelchair (drive position).

NOTE: This allows the motors to drive the wheels.

NOTE: It may be necessary to rock the wheels slightly until the motor release lever engages.

Right Motor

Release Lever

Shown

Disengaged

Engaged

FIGURE 8.2 Engaging/Disengaging Motor Release Lever

Part No. 1148076

49

Pronto® M51Base with SureStep®

Image 49
Contents Pronto M51 Base with SureStep Reference Documents Reference DocumentsDocument Table of Contents Register Your Product Table of ContentsSpecial Notes Special NotesMeaning Trro and Trbkts Warnings Typical Product Parameters Typical Product ParametersLabel Location Label LocationWheelchairs With Trro Wheelchairs Without Trro General Guidelines Controller Settings/Repair or ServiceOperation Information General GuidelinesAccessories Charging Batteries BatteriesWeight Limitation Weight TrainingGrounding Instructions Rain TestEMI Information EMI InformationEMI Information SAFETY/HANDLING of Wheelchairs SAFETY/HANDLING of WheelchairsStability and Balance Coping With Everyday Obstacles Coping With Everyday ObstaclesLifting/Stairways Lifting/Stairways Transferring To and From Other Seats Transferring To and From Other SeatsReaching and Bending Backward Reaching, Leaning and Bending ForwardSafety Inspection Checklists Safety INSPECTION/ TroubleshootingSafety INSPECTION/TROUBLESHOOTING Inspect/Adjust InitiallyInspect/Adjust Weekly Troubleshooting GuideInspect/Adjust Monthly Inspect/Adjust PeriodicallySymptom Probable Cause Solutions General TroubleshootingSPJ+ w/PSS or SPJ+ w/ACC Joysticks Information Gauge Display DiagnosticsDisplay Description Definition Possible Solution Service Indicator Light DiagnosticsMPJ+, PSR+, PSF+ Joysticks or Displays BAD Joystick CAL Values DON’T Checking Battery Charge LevelWheelchair Operation Turning the Power On/OffOperating the Wheelchair Wheelchair OperationMovement Action Using the Joystick to Drive the WheelchairSpeedometer On/Off ButtonSpeed Control Buttons Service IndicatorJoystick Charger/Programming InputDrive Select Toggle Switch MPJ+ Joystick Switches and IndicatorsSelecting the Drive Mode Information Gauge DisplayLCD Display Screens Speed ControlMain Screen Splash ScreenWheelchair Operation Description Status IndicatorRemote Stop Switch Programmable Mono Port 1/2 or External Mode SwitchRemote Mode Reset Switch Connected Devices ScreenMode Switch Remote On/Off SwitchMemory Card Slot Joystick Repositioning JoystickDisconnecting Disconnecting/Connecting the JoysticksConnecting SPJ+ JoysticksTilting the Seat Assembly Back Tilting the Seat Assembly Formula CG OnlySeat SeatTilting the Seat Assembly Formula CG Only Tilting the Seat Assembly ForwardInstalling Removing/Installing the Seat AssemblyRemoving Removing/Installing the Footboard Assembly Footboard AssemblyFootboard Assembly Pinch point may occur when rotating the footboard assemblyAngle Adjusting the Footboard AssemblyDepth Adjusting the Footboard Assembly AngleTOP Shroud and Wheels Removing/Installing the Battery ShroudReplacing the Flat Free Tires on the Wheel Rim TOP Shroud and WheelsRemoving/Installing the Battery Shroud Engaging/Disengaging Motor Release Lever Engaging/Disengaging Motor Release LeverReplacing Front/Rear Caster Assemblies Adjusting ForksBatteries BatteriesNegative Using the Proper BatteriesTool QTY Removing/Installing Batteries from/into Battery TrayRemoving/Installing Batteries from/into Battery Tray Connecting Battery Cables Connecting/Disconnecting Battery CablesCaps not shown on front Disconnecting Battery Cables When to Charge BatteriesSPJ+ w/PSS and SPJ+ w/ACC Joysticks MPJ+ Joystick Charging BatteriesOn-Board Battery Charger Battery Charger OperationON/OFF Indicator Charger Programming Port Transport Ready Package Transport Ready PackageAbout Transport Ready Packages SpecificationsCompliance Information Positioning the Wheelchair in the Vehicle Securing the Wheelchair to the VehicleSecuring the Wheelchair Securement PointsWheelchair-Anchored Belts Securing the OccupantSeating System Vehicle-Anchored BeltsPositioning Belts Positioning BeltsPronto M51 Base with SureStep Pronto M51 Base with SureStep Pronto M51 Base with SureStep USA Limited Warranty