Invacare Pronto M51 Base manual Removing/Installing Batteries from/into Battery Tray, Tool QTY

Page 53

SECTION 9—BATTERIES

Removing/Installing Batteries from/into Battery Tray

WARNING

ALWAYS use the battery handle when lifting the battery. It is the most convenient method and assures that the battery acid will not spill. It also helps to prolong the life of the battery.

DO NOT tip the batteries. Keep the batteries in an upright position.

NOTE: For this procedure, refer to FIGURE 9.2 on page 54.

NOTE: If there is battery acid in the bottom of the battery tray or on the sides of the battery, apply baking soda to these areas to neutralize the battery acid. Before reinstalling the existing or new battery, clean the baking soda from the battery tray or battery being sure to avoid contact with skin and eyes. Determine source of contamination. NEVER install/reinstall a battery with a cracked or otherwise damaged case.

NOTE: Have the following tools available:

TOOL

QTY

COMMENTS

 

 

 

7/16-INCH (6PT) BOX WRENCH

1

Not Supplied

 

 

 

DIAGONAL CUTTERS

1

Not Supplied

 

 

 

Removing

1.Place the wheelchair in a well ventilated area where work can be performed without risking damage to carpeting or floor covering.

2.Verify the joystick On/Off switch is in the Off position and disconnect joystick cable (not shown). Refer to Disconnecting/Connecting the Joystick on page 121.

3.Perform one of the following:

Tilt the seat assembly to the up position. Refer to Tilting the Seat Assembly (Formula CG Only) on page 41.

Remove the seat assembly from the wheelchair. Refer to Removing/Installing the Seat Assembly on page 43.

4.Remove the battery shroud. Refer to Removing/Installing the Battery Shroud on page 47.

5.Disconnect the front battery from the controller (BLACK connector).

6.Disconnect the rear battery from the front battery (RED and BLACK connectors).

7.Lift rear and front battery out of the battery tray using the battery handles.

Installing

1.Verify the joystick On/Off switch is in the Off position and disconnect joystick cable. Refer to Disconnecting/Connecting the Joystick on page 121.

Part No. 1148076

53

Pronto® M51Base with SureStep®

Image 53
Contents Pronto M51 Base with SureStep Document Reference DocumentsReference Documents Table of Contents Register Your Product Table of ContentsMeaning Special NotesSpecial Notes Trro and Trbkts Warnings Typical Product Parameters Typical Product ParametersLabel Location Label LocationWheelchairs With Trro Wheelchairs Without Trro General Guidelines Controller Settings/Repair or ServiceOperation Information General GuidelinesAccessories Charging Batteries BatteriesWeight Limitation Weight TrainingGrounding Instructions Rain TestEMI Information EMI InformationEMI Information Stability and Balance SAFETY/HANDLING of WheelchairsSAFETY/HANDLING of Wheelchairs Coping With Everyday Obstacles Coping With Everyday ObstaclesLifting/Stairways Lifting/Stairways Transferring To and From Other Seats Transferring To and From Other SeatsReaching and Bending Backward Reaching, Leaning and Bending ForwardSafety Inspection Checklists Safety INSPECTION/ TroubleshootingSafety INSPECTION/TROUBLESHOOTING Inspect/Adjust InitiallyInspect/Adjust Weekly Troubleshooting GuideInspect/Adjust Monthly Inspect/Adjust PeriodicallySymptom Probable Cause Solutions General TroubleshootingDisplay Description Definition Information Gauge Display DiagnosticsSPJ+ w/PSS or SPJ+ w/ACC Joysticks MPJ+, PSR+, PSF+ Joysticks or Displays Service Indicator Light DiagnosticsPossible Solution BAD Joystick CAL Values DON’T Checking Battery Charge LevelWheelchair Operation Turning the Power On/OffOperating the Wheelchair Wheelchair OperationMovement Action Using the Joystick to Drive the WheelchairSpeedometer On/Off ButtonSpeed Control Buttons Service IndicatorJoystick Charger/Programming InputDrive Select Toggle Switch MPJ+ Joystick Switches and IndicatorsSelecting the Drive Mode Information Gauge DisplayLCD Display Screens Speed ControlMain Screen Splash ScreenWheelchair Operation Description Status IndicatorRemote Stop Switch Programmable Mono Port 1/2 or External Mode SwitchRemote Mode Reset Switch Connected Devices ScreenMemory Card Slot Remote On/Off SwitchMode Switch Joystick Repositioning JoystickDisconnecting Disconnecting/Connecting the JoysticksConnecting SPJ+ JoysticksTilting the Seat Assembly Back Tilting the Seat Assembly Formula CG OnlySeat SeatTilting the Seat Assembly Formula CG Only Tilting the Seat Assembly ForwardRemoving Removing/Installing the Seat AssemblyInstalling Removing/Installing the Footboard Assembly Footboard AssemblyFootboard Assembly Pinch point may occur when rotating the footboard assemblyAngle Adjusting the Footboard AssemblyDepth Adjusting the Footboard Assembly AngleTOP Shroud and Wheels Removing/Installing the Battery ShroudReplacing the Flat Free Tires on the Wheel Rim TOP Shroud and WheelsRemoving/Installing the Battery Shroud Engaging/Disengaging Motor Release Lever Engaging/Disengaging Motor Release LeverReplacing Front/Rear Caster Assemblies Adjusting ForksBatteries BatteriesNegative Using the Proper BatteriesTool QTY Removing/Installing Batteries from/into Battery TrayRemoving/Installing Batteries from/into Battery Tray Connecting Battery Cables Connecting/Disconnecting Battery CablesCaps not shown on front SPJ+ w/PSS and SPJ+ w/ACC Joysticks When to Charge BatteriesDisconnecting Battery Cables MPJ+ Joystick Charging BatteriesOn-Board Battery Charger Battery Charger OperationON/OFF Indicator Charger Programming Port Transport Ready Package Transport Ready PackageCompliance Information SpecificationsAbout Transport Ready Packages Positioning the Wheelchair in the Vehicle Securing the Wheelchair to the VehicleSecuring the Wheelchair Securement PointsWheelchair-Anchored Belts Securing the OccupantSeating System Vehicle-Anchored BeltsPositioning Belts Positioning BeltsPronto M51 Base with SureStep Pronto M51 Base with SureStep Pronto M51 Base with SureStep USA Limited Warranty