ResMed 338425/1 manual Using the Data Card to Update Settings

Page 27

1 Insert the Data Card

•Switch on the S8 Elite II and wait until you see the standby (RAMP) screen.

•Hold the Data Card with the arrow facing up, and insert it into the slot in the Data Card module (H-1).

•Push the card in smoothly until it stops moving (H-2) and messages start appearing on the LCD.

2 Copy Data onto the Data Card

•Data copying starts automatically when the Data Card is inserted into the Data Card module.

•The “Card Inserted Please Wait” message is displayed on the S8 Elite II LCD while data is being copied. Copying takes up to 30 seconds.

•The “Copy Complete Remove Card” message is displayed on the LCD when copying has finished.

•Remove the Data Card from the Data Card module. No additional data is copied onto the card once the "Copy Complete Remove Card" message is displayed, even if the card is left in the device. To add additional data to the Data Card, reinsert the card and repeat these steps.

3 Remove the Data Card

Grip the end of the Data Card and pull it out of the Data Card module (H-3).

4 Store the Data Card

Your Data Card should be stored in its mailback envelope when not in use.

5 Mailing the Data Card to your Clinician

When mailing the Data Card to your clinician:

1.Insert the Data Card into the pocket provided on the mailback envelope. Fold up the mailback envelope.

2.Place the mailback envelope containing the Data Card in a postal envelope and seal it.

3.Make sure that your clinician’s name and address details are on the postal envelope, and mail it back immediately.

Using the Data Card to Update Settings

If your clinician has provided a Data Card with new device settings:

•With the device in standby (Ramp) mode, insert the Data Card into the slot on the Data Card module. Updating will start automatically.

•The “Card Inserted Please Wait” message is displayed on the LCD while updating is in progress. Updating takes up to 30 seconds.

•The “Settings Success Remove Card” message is displayed on the LCD if the settings were updated successfully.

Note: This message only appears once. If you re-insert the Data Card after you have updated your settings, this message is not displayed.

•Remove the Data Card from the Data Card module.

S8 Modules

21

Page 26 Page 28
Image 27
Page 26 Page 28
Contents S8 Elite II System Page S8 Elite II System Blank Module Contents Replacing the Air Filter Servicing Your Responsibility IntroductionMedical Information About the S8 EliteContraindications Page Adverse Effects S8 Elite II System S8 EliteMasks Accessories HumidifierResScan Data Card Module How to Use the S8 Elite Set Up the S8 EliteAssemble the Mask Start Treatment Stopping TreatmentSmartStart Excelnt Page How to Attach a Humidifier Attach a HumidAire 3i HumidifierStoring the HumidAire How to use the Keypad LCD ScreenKeypad Keys How to Change the Ramp Time How to Change the SettingsHow to Use the Standard Menu How to Change the Expiratory Pressure Relief SettingHow to Select the Mask Type Other viewable information Shows the detailed menu How to Use the Detailed MenuHow to Change the SmartStart Setting Settings MenuHow to Change the Tube Length How to Add a Humidifier or Front CapMessages on the S8 Elite II LCD Results MenuOptions Menu Servicing MenuReplace Using a Blank Module Using a ResScan Data Card ModuleS8 Modules Using the Data Card to Update Settings Page Periodic Cleaning Cleaning and MaintenanceDaily Cleaning Weekly CleaningServicing Replacing the Air FilterFrequently Asked Questions Can I use my S8 Elite II if mains AC power is not available? No display TroubleshootingSystem ERR nnnn Leak Settings Success Remove Card S8 Elite II no Accessories System SpecificationsAll Devices where applicable Data CardData Card Module Symbols which appear on the device R001-307/1 System Specifications Portable and mobile RF communications Separation distance according to frequency of transmitter Limited Warranty Index PCB
Top Page Image Contents