Ericsson LBI-38377E manual Adding Channels To And Deleting Channels From The Scan List

Page 19

CONTROL KNOB will not change channels. Turning the radio off and back on will reset this condition.

∙GE-STAR is sent on the selected channel and the radio locks onto that channel. Rotat- ing the CONTROL KNOB will not change channels. Turning the radio off and then back on will reset this condition.

SCANNING CHANNELS (Scan and System models)

The M-PA may be programmed for non-priority scan, dual-priority scan, or scan operation may be disabled. Scan programming options include a key- pad entered scan list or a fixed scan list. Priority scan programming options include a fixed priority-one channel or the selected channel as the priority-one channel.

The radio may be programmed to scan only the channels in the current mode or it may be pro- grammed to scan across modes.

Scan rate will vary depending upon the number of channels on the scan list and whether or not the radio is programmed to scan for Channel Guard. Fewer channels will result in a faster scan rate. All

scan functions are retained in memory when the battery pack is removed.

The radio will not scan when the emergency mode is enabled ("EMG" status flag is on).

Adding Channels To And Deleting Channels From The Scan List

If the "SCAN A/D" menu is programmed, chan- nels may be added to and deleted from the scan list of each mode as follows:

1.Select the desired mode and channel. If the selected channel is currently on the list, the "S" status flag will be on.

2.Press the MENU button until "SCAN A/D" is displayed.

3.Press the SEL button until the desired pri- ority indicator appears: "S" for non-priority, "2" for priority-two, "1" for a priority-one, or no indicator to remove the channel from the scan list. If a new priority channel is se- lected the previous corresponding priority channel will become a non-priority scan

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operator’s Manual Ericsson Inc Table of Contents TTD Safety Not ApplicableControl Knob Controls ON/OFF SwitchVolume Control Knob IntroductionMonitor Button PTT ButtonEmergency Button PA Personal Radio Side View Front View KEY Lock Allows the keypad buttons to be locked or unlocked Alert Allows the alert tones to be dis- abled or enabledMenu Button Scan Model Menu DisplayMode Exit ButtonScan Button ChannelPA System Model Radio Select Button Dtmf Keypad IndicatorsUniversal Device Connector TX Transmitter enabled On when the radio is transmittingChannel Busy Carrier Control TimerOperation POWER-UP Alert TonesMODE/CHANNEL/CG Selection Press the Menu button until Mode ap- pears in the displayPress the Menu button until Channel appears in the display Receiving a Message Adjust the volume as necessaryListen for a reply Transmitting a MessagePress the Menu button until Scan A/D is displayed Adding Channels To And Deleting Channels From The Scan ListScan Model Using ScanScan DIS - The radio is not programmed to scan Telephone Interconnect CallsPress the Menu button until Phone ap- pears in the display If the SCN status flag is on, press Scan to turn scan offPlacing a Manually Dialed Call Telephone Interconnect Calls System ModelsPress and hold the PTT Button to key the transmitter Placing An Automatically Dialed Call Release the PTT Button when the dial sequence is completeWhile holding the PTT BUTTON, press Release the PTT Button and listen for a dial toneKEY Lock Menu Scan and System models Lock The KeypadUnlock The Keypad Disable The Alert TonesEnable The Alert Tones Programmable FeaturesRadio Programmable Programmable by ChannelOperating Tips When using your two-way radio, remember these rulesBattery Packs Installing the Battery Pack Removing the Battery Pack Installing the Battery PackContains a rechargeable, recyclable Swivel Mount Removal ReplacementBatteries Intrinsically Safe UsagePacity Short Case Accessories Warranty Warranty becomes void if NICKEL-CADMIUM Battery WarrantyPage Emergency Numbers
Top Page Image Contents