Ericsson LBI-38377E manual Transmitting a Message, Listen for a reply

Page 18

TRANSMITTING A MESSAGE

EMERGENCY OPERATION

1.Select the desired mode, channel, and/or Channel Guard. See the MODE/CHAN- NEL/CG SELECTION for details..

2.Ensure no one is transmitting on the se- lected channel by pressing the MONITOR BUTTON to disable squelch or observing the display for the absence of the "BSY" status flag. If the Channel Busy Lockout feature is programmed for the selected channel, the radio will not transmit when the channel is busy.

3.Press and hold the PTT BUTTON. The "TX" and "BSY" status flags are displayed.

4.Hold the radio approximately three inches from your mouth and speak into the micro- phone in a normal voice.

5.Release the PTT BUTTON when the trans- mission is complete. If the transmission exceeds the programmed Carrier Control Timer limit, the radio will unkey and an alert tone will sound.

6.Listen for a reply.

The radio may be programmed to transmit GE- STAR emergency signalling when the EMERGENCY BUTTON is pressed or from a UDC connected lan- yard. If the EMERGENCY BUTTON is programmed for GE-STAR emergency activation, press it for ap- proximately one (1) second to activate the transmis- sion. If the lanyard is programmed for activation, follow the instructions provided with it. GE-STAR is programmed to transmit in one of the following meth- ods:

∙GE-STAR is transmitted on a predetermined mode and channel regardless of the selected channel. In this case the selected channel is available for voice and the radio will peri- odically "jump" to the predetermined channel and send the emergency message and then "jump back" to the selected channel for voice operation.

∙GE-STAR is transmitted on the selected channel. If the channel is changed the emer- gency bursts will follow the newly selected channel.

∙The radio switches to and stays on a prede- termined mode and channel and GE-STAR is transmitted on that channel. Rotating the

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operator’s Manual Ericsson Inc Table of Contents Safety Not Applicable TTDIntroduction Controls ON/OFF SwitchVolume Control Knob Control KnobPTT Button Monitor ButtonEmergency Button PA Personal Radio Side View Front View Menu Display Alert Allows the alert tones to be dis- abled or enabledMenu Button Scan Model KEY Lock Allows the keypad buttons to be locked or unlockedChannel Exit ButtonScan Button ModePA System Model Radio Select Button Indicators Dtmf KeypadTX Transmitter enabled On when the radio is transmitting Universal Device ConnectorAlert Tones Carrier Control TimerOperation POWER-UP Channel BusyPress the Menu button until Mode ap- pears in the display MODE/CHANNEL/CG SelectionPress the Menu button until Channel appears in the display Adjust the volume as necessary Receiving a MessageTransmitting a Message Listen for a replyAdding Channels To And Deleting Channels From The Scan List Press the Menu button until Scan A/D is displayedTelephone Interconnect Calls Using ScanScan DIS - The radio is not programmed to scan Scan ModelIf the SCN status flag is on, press Scan to turn scan off Press the Menu button until Phone ap- pears in the displayTelephone Interconnect Calls System Models Placing a Manually Dialed CallPress and hold the PTT Button to key the transmitter Release the PTT Button and listen for a dial tone Release the PTT Button when the dial sequence is completeWhile holding the PTT BUTTON, press Placing An Automatically Dialed CallLock The Keypad KEY Lock Menu Scan and System modelsProgrammable Features Disable The Alert TonesEnable The Alert Tones Unlock The KeypadProgrammable by Channel Radio ProgrammableWhen using your two-way radio, remember these rules Operating TipsBattery Packs Installing the Battery Pack Installing the Battery Pack Removing the Battery PackSwivel Mount Removal Replacement Contains a rechargeable, recyclableIntrinsically Safe Usage BatteriesPacity Short Case Accessories Warranty NICKEL-CADMIUM Battery Warranty Warranty becomes void ifPage Emergency Numbers
Top Page Image Contents