Lifescan SureStep Pro manual New Test Memory full Space Data

Page 101

	MESSAGE	POSSIBLE	SOLUTION
	MESSAGE	CAUSE	SOLUTION
		CAUSE

	No Room for	Bedside unit	Transfer data to free memory
	New Test	memory full.	space.
	Data

	No Room for	There are five new	Transfer data and validate
	New Test	(non-validated)	new test strip lots.
	Strip Lot	test strip lots in
		bedside unit list.

	Phone Line	1. Workstation	1.Workstation modem’s
	Busy at	modem phone	phone line must be a
	Workstation	line being used	dedicated line. Do not
		by fax machine.	share line with a fax
			machine.
		2. Faulty telephone	2.Have phone line inspected.
		line.

	QC Due for	Unit will be in QC	Perform required QC tests
	Bedside Unit	lockout if required	within 2 hours.
	in Less than	QC not performed
	Two Hours	within 2 hours.

	QC Due:	QC overdue or QC	Successfully perform all
	QC Missed or	test failed.	required QC tests.
	Failed

	Reagent Lot	Reagent (solution)	Enter and use new reagent
	Expired	lot expired.	lot. Discard any remaining
			expired reagent.

	Remove Strip	Not enough	Remove test strip. Check
	appears after	sample on test	confirmation dot. If white
	you insert	strip or test strip	patches or streaks appear, not
	test strip.	inserted too	enough blood was applied for
		quickly.	an accurate result. Repeat test
			with new test strip.
			When “Insert Strip” appears,
			firmly and more slowly insert
			test strip until it stops.

If you cannot resolve a problem, call LifeScan Healthcare Professional Line:

1 800 524-7226 (USA)

1 888 353-0800 (Canada)

89

Image 101

Contents Bedside Unit Operator’s Guide Page It should not be used for Diagnosis of diabetes 2002, 1996 LifeScan, Inc. All rights reserved Table of Contents Table of Contents Preface About This Guide PrefaceVii Conventions Used in This Guide Help Preface Introduction Introduction Front Bedside UnitTest Strip Holder General Operating Information Main Menu lets you select from six different functions Page Scanning a Barcode SureStepPro Test Strips Frontback Important Test Strip Information Precautions Page Infection Control Quality Control Test Quality Control Test When to Perform a Quality Control TestGlucose Control Solutions Performing a Quality Control Test Page Select the control level you wish to run for example, High Select the test strip lot Applying Control Solution to Test Strip Page Quality Control Test Page If the result is Failed Page Quality Control Test Performing a Patient Test Patient TestPatient Test Page Patient Test Applying Blood Sample to Test Strip Apply the blood to the test strip as follows Syringe Front Page Critical High indicates a result above the range Page Patient Test Transferring Data to the Workstation Data ManagementData Management Page Using the Connection Module Select Transfer Data from the Main Menu SureStepPro 2.0 Users Ethernet Last Data Transfer mm/dd/yy hhmm Failed Bedside Unit Memory If you select Patient If you select QC/Lin/Unkn Press Menu to proceed, or turn off the bedside unit General Care Care and MaintenanceCleaning the Test Strip Holder and Lens Cleaning the Outside of the UnitContact points Lens area Care and Maintenance Changing the Batteries Care and Maintenance Page Adjusting the Screen Contrast Linearity Test Special TestsSpecial Tests Select Lot # Special Tests Page Special Tests Page Special Tests Unknown Solution Test Special Tests HIGH003 Special Tests Page Do not remove the test strip until the countdown is complete In-Service Test Select In-Service Mode from Special Tests menu Troubleshooting Troubleshooting Error Possible Solution Cause Error MessagesError Possible Solution Clean bedside unit Detected a Make sure test strip With water to remove Unexpected Messages and Observations Message Possible Solution Cause Check Data Re-enter your ID using New Test Memory full Space Data Shake vial Bedside unit is Patient Results Bedside Unit Configuration OptionsBedside Unit Bedside Unit Configuration OptionsNot need to enter Operator and IDs Quality Control QC Test Period Frequency of performing a Bedside Unit Specifications SpecificationsBarcode Specifications SpecificationsType BF Equipment Cleaning Agents Index Index Unknown solution test Workstation Page For use with bedside units, versions 1.2