Microsoft MN-820 manual Establish Your Internet Settings

Page 27

4.In the Confirm new password box, retype the new password.

5.To save the new password, click Apply.

Be sure to store your password in a safe place. If you forget or misplace your password and cannot log on to the Base Station Management Tool, you can restore the base station to the factory default settings from the base station itself, and then use the default password admin to open the Base Station Management Tool. For more information about restoring factory default settings to the base station, see Chapter 1, “Introduction.”

Step 4: Establish Your Internet Settings

On the Wide Area Network page of the Base Station Management Tool, you must specify whether you have a dynamic, static or Point-to-Point Protocol over Ethernet (PPPoE) Internet connection. Depending upon the type of Internet connection you have and your ISP account, you will be required to specify additional Internet settings information, such as your host name, subnet mask, or domain name server (DNS) address. This information is typically provided by your Internet Service Provider (ISP).

If you need assistance determining your Internet settings, see Appendix A, “Locating Your Internet and Network Settings.”

1.From the Base Station Management Tool, click Wide Area Network. On the Wide Area Network page, under Internet Connection Type, select the type of Internet connection provided by your ISP.

2.Enter the information required for your specific Internet connection type.

O If you selected Dynamic, under Dynamic Connection, specify a host name if your ISP requires it. Specify the DNS primary and secondary addresses, if your ISP provided you with this information. If you are replacing an existing base station, router, or gateway with the Microsoft base station, specify the media access control (MAC) address of that device in the MAC Address box, and then click Clone MAC Address. Otherwise, specify the MAC address of the adapter that was connected to the modem in the MAC Address box, and then click Clone MAC Address. For information about MAC addresses, see Broadband Network Utility Help.

O If you selected Static, under Static Connection, type the IP address, subnet mask, default gateway IP address, and DNS addresses provided by your ISP.

O If you selected PPPoE, under Point-to-Point Protocol over Ethernet (PPPoE), type your user name and password, the service name if your ISP provided it, and the maximum idle time, if your ISP instructed you to do so. You will be disconnected from the Internet if the time that you specify elapses without activity. Select the Auto-reconnect check box to reestablish the connection automatically after a disconnect.

3.To save the wide area network (WAN) settings you have entered, click Apply.

Chapter 3: Custom Setup 21

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Page Avertissement Contents Using an Internet Connection over a Network Contents Page Your Wireless Base Station About Your Wireless Notebook KitBase Station Ports, Status Lights, and the Restore Button UPnP Standards and Your Wireless Base StationIntroduction To detach the stand Using the Base Station StandResetting the Base Station To attach the standYour Wireless Notebook Adapter Restoring Factory Default SettingsTo restore the base station to factory default settings Windows 98, Windows 98 SE, and Windows Me Adapter Status LightsCardBus Technology Windows XP or WindowsTypes of Wireless Networks About Wireless Radio ConnectionsPlacement of Wireless Components Understanding Wireless Transmission Standards Adjusting the Base Station AntennaEthernet Cables About Wired Ethernet ConnectionsTypical Setup SetupIf… Do this first… Gather Components, Tools, and InformationConnect the Base Station Run the Setup Wizard to Set Up the Base StationConfigure the Base Station Insert the Adapter into Your Computer Configure Your Adapter Test Your NetworkWhat’s Next? To set up the base station wirelessly Setting Up the Base Station WirelesslyPage Custom setup Base Station Setup Establish the Base Station PasswordOpen the Base Station Management Tool Establish Your Internet Settings Establish Your Wireless Security Settings Establish Your Wireless SettingsConfigure Your Computer Customize Network SettingsTest your Internet Connection Connect the Base Station to a Computer Access Point SetupEstablish the Base Station Password Set the Base Station to Access Point Mode Page Network activities Using an Internet Connection over a Network Logging on to Your NetworkTo log off and log back on to your network To remove an inactive device from the Network Devices list Using the Broadband Network UtilityTo start the Broadband Network Utility To refresh the Network Devices listTo share a folder or drive on your computer in Windows Using Files and Folders over a NetworkMake your files and folders available to the network To share a folder or drive on your computer in Windows XPTo access shared files on other computers Access shared filesUsing a Printer over a Network Using Other Peripheral Devices over a Network About Reading E-Mail Messages on a NetworkPlaying Games on Your Network and on the Internet Creating a Computer-to-Computer Ad Hoc Network To set up an ad hoc network in Windows XPTo join an available network in Windows XP Joining an Available Wireless NetworkPage To refresh the network device list Monitoring Your NetworkView Status View Network DevicesUpdating Software, Drivers, and Firmware View Adapter SettingsTo view adapter settings To upgrade software, drivers, or firmwareHelp Protect Your Network from Hackers Help Protect Your Network from Computer VirusesHelp Protect Your Network from Unauthorized Access Setup and Hardware Problems TroubleshootingIf your base station is connected with an Ethernet cable Setup does not recognize my wireless base stationSetup does not recognize my wireless notebook adapter If your base station is connected wirelesslyTroubleshooting To clone a MAC address Troubleshooting Network and Internet Problems Can’t stay connected to my wireless networkTo disable 802.1x authentication in Windows XP Troubleshooting Page Troubleshooting My network is slow Troubleshooting Page Can’t print to a networked printer Printing and File Sharing IssuesPage Troubleshooting Click OK to save the changes If the file is stored on a Windows XP-based computerTo determine which connection type your ISP provides Internet Connection TypeHost Name General Internet SettingsDynamic IP Dhcp Settings To locate your Internet settingsStatic IP Settings To locate your static IP address settings Windows XPTo locate your static IP address settings Windows PPPoE Settings Workgroup NameTo determine your workgroup name in Windows XP or Windows Wireless Network Name Wireless Security SettingsTo determine your workgroup name in Windows Me and Windows Technical Support Options Getting HelpRegulatory Information United States Radio and TV Interference RegulationsCanadian Radiocommunication Regulations Base Station Technical SpecificationsTo +40 deg C To +35 deg C System Requirements END-USER License Agreement for Microsoft Software General Provisions Limited Warranty Contrat DE Licence Utilisateur Final Pour Logiciel Microsoft Dispositions Générales Garantie Limitée Page Glossary Page Glossary Page Glossary Page Index Page Index Typical Setup base station, 11 preparing for My Network Settings
Top Page Image Contents