Siemens 2060isdn manual Enable/disable base station change with call in progress

Page 87

8.12.98

I_KAP05.FM5

Gigaset 2060isdn, Inland:

A30853-X210-B101-1-19

Multicell system

Enable/disable base station change with call in progress

You can register and operate the mobile units at different base stations from the Siemens Gigaset family, including non-ISDN base stations.

In order to prevent a call being switched to a non-ISDN base station, you must define the base stations to which switching is permitted.

The comfort mobile unit is idle.

Ž

.t Settings

tStation 1-6

tMeaning: see footnote

t Station settings

Select the station you want to define as “park-compati- ble” and open the submenu.

xW t

Multicell config

u

u

ON

OFF

x

x

OK

or

OK

Set the station you selected to “Parking active” (i.e. calls can be switched to this base station).

Set the station you selected to “Parking inactive” (i.e. calls cannot be switched to this base station).

Press { if you want to cancel.

A “P” indicates a base station from which or to which calls can be switched.

Switching to another base station while conducting a call

uCHANGE

If you have configured a multicell system consisting of at least two ISDN base stations, you can switch from the ra- dio area of one base station to the other while an external call is in progress without having to terminate the call.

If you move to the limit of the radio footprint of one base station and want to move to the next base station, notify your partner that you are going to interrupt the call briefly in order to switch base stations. Then proceed as de- scribed below in order to resume the call via the other base station.

You are conducting an external call.

Press this softkey to change from the radio footprint of one base station to that of the other base station.

Resume your external call.

tmeans: browse with u

Z or u NEXT

and press x

OK

to confirm

87

Image 87
Contents Corded terminals can be connected Gigaset 2060isdn, InlandYour corded equipment is now ready for use Installation steps for the Gigaset 2060isdnGetting started Getting startedFront view Rear view Carry clip OverviewsOverviews Standard mobile unit, 2000SOverviews Contents Contents Index 107 101103 105Safety instructions Safety instructionsCertification for basic access and telephone systems Base station InstallationInstallation Contents of package Base stationConnecting the base station Initial registration Press the Register button on the base stationYour mobile unit is registered and ready for use Registering at more than one base station and Gigaset 1000C RegisterThen proceed with the base station Press Installation System codeDelete MSN Installation Saving multiple subscriber numbersService New entry MSN listEntering/changing collective call Installation Ring allocationWall-mounting the base station Ring allocation Coll. callTips on where to install the base station Selecting the locationRange Point-to-point Important information about Euro-ISDNConnection options base station Types of connection Point-to-multipointOperating information and error messages FeaturesUsing the menus Operation with comfort mobile unitOperation with comfort mobile unit Menu structure for system settings Ext. consultat’nResume Example External consultation in external call Idle state Example illustrating the menu hierarchyEntering/changing the system code Basic settingsBasic settings System settings t Change sys. codeBasic settings Setting point-to-multipoint System settings Configuration Point to MPLocal op Multicell op Basic settings Setting point-to-point System settings Configuration Point to PP phonenumber Press to activate call pickup Basic settings Suppressing phone-number displayActivating/deactivating call pickup Anonym. call Anonym. answerCall waiting STN Service System settings Device dataPress OK if you merely want to check the setting Activating/deactivating automatic line seizureBasic settings Administrating the list of calls Incoming calls Incoming callsAnswering/terminating a call Internal users Meaning Incoming calls Call pickupAnswering a waiting call with another call in progress Incoming calls Call pickup from answering machineIntercept on Incoming calls Tracing a call call intercept/MCIDOutgoing calls Outgoing callsDialing external numbers with the keypad List of calls t Display entry Outgoing calls Viewing/dialing from list of callsTerminating an internal call Outgoing calls Dialing internal numbersCalling an internal user Collective call to all mobile units/devicesOutgoing calls Activating Anonymous call for a single call Servicet Anonym. callHolding an internal call Internal Call in progressCall in progress Holding a callTo reset the dialing function deactivate Temp. tone Press the softkey to reset the dialing functionTemp. tone Call in progress Mute function Switching to keypadExternal consultation Switching functionsSwitching functions Internal consultation/call transferToggling between external users TogglingResume Toggling between internal and external usersEnding toggle mode Three-party conferenceEnding the three-way conference Switching functions Parking an external call Unparking an external callActivating external call forwarding Ext./direct Ext./busy Ext./timeout Ox OKDeactivating external call forwarding Deactivating internal call forwarding Activating internal call forwardingDeactivating external automatic callback Switching functions Activating external automatic callbackCall charges, call duration Call charges, call durationDisplaying call charges/call duration Units/charges Activate/deactivate display of charge units System settings t Duration/unitsCall duration Activate/deactivate display of call durationCall charges, call duration Lock on Phone No. list New entry Delete phone No LocksLocks Lock for outgoing calls system lock/emergency phone numbersLock int2 Lock on System settings Call barring Delete allDelete all lock numbers Blocking unwanted callsSetting user access rights Internal user System settings Device data Access rightsLine System settingsSystem settings Setting internal collective callEnabling/disabling trunk hold System settings Device data Auto. DtmfSystem settings Device data Trunk hold System settings Device data Dial * and #System settings Reinitializing the base station Ring allocation for point-to-multipoint accessReset Deleted Not changed 78901234 456789001 Collective callExample External phone num- bers 78901234 45678901Enter/change group calls Enter/change collective callExample External phone No Call group Ring allocationExample External phone No Call group 12345678 Diversion dest Set call forwarding with group call Group diversionSelect Group diversion Service Unregister System settings Unregistering a mobile unitGigaset 2000S 1000S Operation with other mobile unitsOperation with other mobile units Gigaset 1000C# 8 *SC* new SC new SC B Basic settingsIncoming calls Outgoing callsCall in progress # 4 1 3O MSN Switching functionsLocks Call charges, call durationMulticell operation Operation with door intercom int. NoSockets see illustration, Connecting corded devicesOperation with supplementary devices Operation with supplementary devicesSetting the device type Connecting telephonesConnecting corded devices other than telephones General Dialing an external number using the keypadActivating anonymous call for a single call Controlling answering machines/using telephone servicesAnswering call waiting Operation with supplementary devices Incoming callsCall pickup/pickup from answering machine Supplementary device is idleOperation with supplementary devices Switching functions Call transfer without consultation Consultation call/call transferStarting an internal consultation call Terminating an internal consultation callGigaset 2060isdn , Inland Activating external automatic callback Toggling with a telephone set to Dtmf dialingThree-party conference Or terminate the three-party conferenceDeactivating external automatic callback Parking an external connectionUnparking the external call Terminals of the TFE adapter box Examples of how to connect door intercoms via TFEOperation with door intercoms Operation with door intercomsRecommendation Ring allocation for the door intercom Connection to supplementary device Connection to comfort mobile unitMulticell system Possible combinations General remarksOrganization of base stations and mobile units 150m Registering comfort mobile units at multiple base stations Multicell system Setting multicell operation Preferred search Setting automatic base station selection Select stationSwitching to another base station while conducting a call Enable/disable base station change with call in progressOperation behind a private branch exchange General remarks Activating PBX featuresExample setting up a consultation call Or switch the callSystem settings Device data Transfer call Other Euro-ISDN featuresExamples General notes Ring signalsAcoustic signals General notesElectrostatic buildup Technical dataWipe the mobile units and base station clean with a General notes System upkeepProblem Possible cause Remedy General notes TroubleshootingContact partners General notes WarrantySiemens Service Telephone in Germany Service hours Monday to Friday Am 7 pm Saturday Am 2 pmSuppressing transmission of phone number Frequently asked questionsFrequently asked questions Call charge/totals managementDevice type ID Selective call enableAnonymous answer Callback on BusyPrivate branch exchange behind Gigaset 2060isdn Answering machinesMusic on hold Parking call transfer on busGigaset 2060isdn behind a PBX RoamingHandover Call forwarding Call waiting GlossaryGlossary Automatic call backExtension number Emergency phone numberEn-bloc dialing Euro-ISDNToggle System codeThree-party ConferenceQuick-reference guide, comfort mobile unit Xz x Dial Quick-reference guide, supplementary device Park external call Sion to initiate a three-party conferenceParty’s telephone for this call Seize the line and enter the phone numberGigaset 2000H Special accessoriesSpecial accessories Gigaset 2000CGigaset 1000TAE Special accessories Gigaset 2000T109 Index110 111 Siemens Aktiengesellschaft BACKPAGE.FM