Diagram KEY, Important Safety Information

DIAGRAM KEY

1	Dial Mode Switch (Pulse/Tone)	10	Volume Control
2	Audio Output Socket	11	Low Battery Indicator
3	Telephone Line Connection	12	Visual Ring Indicator
4	Ring Tone Switch	13	Amplify Button
5	Ringer Volume Switch	14	Amplify Indicator
6	Telephone Number Directory	15	Programme Button
7	Memory Buttons	16	Call On Hold Indicator
8	Redial Button	17	Tone Control
9	Flash/Recall Button	18	Call Hold Button

IMPORTANT SAFETY INFORMATION

PLEASE READTHE FOLLOWING INSTRUCTIONS BEFORE USE:

When using your telephone equipment these basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons including the following:

Read and understand all instructions.

Follow all warnings and instructions marked on the telephone.

Please ensure this product is disconnected from the telephone line cable before installing or replacing batteries.

Do not dispose of batteries in a fire.They may explode.Take empty batteries to a collection point for chemical waste.

Do not install or use this telephone near water.

Avoid using a telephone (other than a cordless type) during a storm.There may be a remote risk of electrical shock from lightning.

Unplug this telephone from the wall outlets before cleaning. Do not use liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth for cleaning.

Do not cover the slots and openings on this telephone.This telephone should never be placed near or over a radiator or heat register.This telephone should not be placed in a built-in installation unless proper ventilation is provided.

Do not place anything on the telephone line cable. Install the telephone where no one will step or trip on the cable.

Never push any objects through the slots in the telephone.They can touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock. Never spill liquid of any kind on the telephone.

	UK

	To reduce the risk of electrical shock, do not take this phone apart. Opening or removing covers		UK
	may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric

	shock when the appliance is subsequently used.
	Never install telephone wiring during a lightning storm.
	Hereby, Plantronics BV declares that the Clarity™ EXL30 Amplified Telephone is in		D
	compliance with the essential requirements and all other relevant provisions of

	Directives 1999/5/EC and 93/42/EEC.
	To view the Declaration of Conformity for this product please see
	www.plantronics.com/documentation		E
	Class I medical device
	When the Amplified Indicator (14) is illuminated, the volume may be very loud and
	in excess of 118dB.This mode is intended specifically for hearing impaired users.		F

	GETTING STARTED
	INSTALL BATTERIES
	Please ensure this product is disconnected from the telephone line cable before		I
	installing or replacing batteries.

To add extra brightness to the EXL30’s Visual Ring Indicator (12), install one 9 Volt alkaline battery (not included).

TO INSTALLTHE BATTERY	NL
TO INSTALLTHE BATTERY
Fig.A Use a pen to open the battery door (see instructions underneath the telephone unit)
Slide open the battery compartment cover on the bottom of the telephone, install the
battery, and replace the cover.
SETTINGTHE DIALLING MODE
Set the Dial Mode Switch (1) to T (tone) if you have touch tone DTMF service. Otherwise set
the switch to P (pulse).

CONNECTING FOR WALL MOUNT OR DESKTOP USE

WALL MOUNTING

Drill two holes in the wall 10.2cm (4") apart adjacent to the mounting holes on the telephone. Use the correct screws to hang the telephone on the wall.

Fig. B Slide the handset hook out as shown in Fig. B and reverse its position so that the hook points up and will hold the handset when you hang up.

Fig. C Insert the tabs of the phone base into the slots in the lower position of the base as shown in Fig. C. Push the mounting bracket in and down firmly until it snaps into place. Position on the wall close to your telephone wall socket.

Clarity EXL30 manual Diagram KEY, Important Safety Information, Getting Started

DIAGRAM KEY

IMPORTANT SAFETY INFORMATION

PLEASE READTHE FOLLOWING INSTRUCTIONS BEFORE USE:

GETTING STARTED

INSTALL BATTERIES

Fig.A Use a pen to open the battery door (see instructions underneath the telephone unit)

Slide open the battery compartment cover on the bottom of the telephone, install the

battery, and replace the cover.

SETTINGTHE DIALLING MODE

CONNECTING FOR WALL MOUNT OR DESKTOP USE

WALL MOUNTING

Fig. B Slide the handset hook out as shown in Fig. B and reverse its position so that the hook points up and will hold the handset when you hang up.

Fig. C Insert the tabs of the phone base into the slots in the lower position of the base as shown in Fig. C. Push the mounting bracket in and down firmly until it snaps into place. Position on the wall close to your telephone wall socket.

Fig. D Connect the Telephone Line Cable and the Handset Cable to the telephone.

If required, use the supplied adapter.

Lift the handset and listen for a dial tone.