Panasonic KX-TCD440NZ Battery charge, Battery strength, Battery icons, Battery life, Operation

Page 7

Battery charge

Preparation

Battery charge

Place the handset on the base unit for about 7 hours before initial use.

Note:

L Clean the charge contacts of the handset and base unit with a soft, dry cloth once a month, otherwise the batteries may not charge properly. Clean more often if the unit is exposed to grease, dust or high humidity.

Battery strength

When charging, the battery icon is shown as follows.

L When the batteries are fully charged, 054 flashes.

Battery icons	Battery strength
5	High

6	Medium

7	Low

074	Needs to be charged

Note:

L If the handset is turned off, it will be turned on automatically when it is placed on the base unit.

Battery life

After your Panasonic batteries are fully charged, you can expect the following performance:

Ni-MH batteries (typical 700 mAh)

Operation	Operating time
While in use (talking)	10 hours max.
While not in use	200 hours max.
(standby)

Ni-Cd batteries (typical 250 mAh)

Operation	Operating time
While in use (talking)	4 hours max.
While not in use	60 hours max.
(standby)

Note:

L The included batteries are Ni-MH batteries.

L Battery operating time may be shortened depending on usage conditions and ambient temperature.

7

Image 7

Contents Model No. KX-TCD445NZ Digital Cordless PhoneDigital Cordless Answering System Model No. KX-TCD440NZPreparation Useful Telephone SettingsAnswering System Features KX-TCD445 only Table of ContentsPreparation Accessory informationIncluded accessories Additional/replacement accessoriesEnvironment Battery cautionImportant information GeneralA Speaker B k Phonebook C C Talk D Navigator I Receiver J Display K R Redial/Pause L j Menu/OK M ih Off/PowerLocation of controls HandsetA Charge contacts B x Page Battery installationConnections Base unitBattery life Battery chargeBattery strength Battery iconsPower off Battery replacementTurning the power on/off Power on8 cm Screws Hooks Wall mountingL Make sure the screws are securely fastened to the wall Making calls Redial featureTo adjust the receiver or speaker volume To make a call using the redial listTo store a number from the redial list into the phonebook Other featuresR button to use the recall feature Pause button for PBX line/long distance service usersRecording a telephone conversation KX-TCD445 only Auto talk featureAnswering calls Handset locatorTo edit/correct a mistake Editing a stored entryErasing a stored entry KeysAssigning an entry in the phonebook to a hot key Making calls using the phonebookMaking calls using a hot key Hot key quick dialViewing caller information and calling back Caller ID serviceUsing toll services from Telecom or another company Call minderExample Editing a caller’s phone number before calling backErasing caller information Storing caller information into the phonebook2nd menu Guide to handset settingsUseful Telephone Settings Default settingChanging the alarm frequency Handset settingsTime alarm Setting the time of alarmExample Selecting the talk mode display Tone optionsDisplay options Selecting the standby mode displayStoring the direct call number Setting call barCall options Selecting the display languageOther options Setting auto talkSetting the battery type Resetting the handset to its default settingsSetting recall time Guide to base unit settingsBase unit settings Adjusting ringer volumePage L The emergency number setting will not be reset Resetting the base unit to its default settings3 Press 4 Enter “0000” default base unit PIN L For the default settings, see pagePlaying back the greeting message Answering System Features KX-TCD445 onlyUsing a prerecorded greeting message Recording a greeting messageErasing the greeting message Recording a voice memoErasing all messages Turning remote operation on/off Using the answering system remotelyMemory capacity Remote operationTurning on the answering system remotely Guide to answering system settingsRemote commands Remote commandTurning the recording quality on/ off Selecting the caller’s recording timeTurning the monitor on/off Additional handsets Operating additional unitsRegistering a handset to a base unit Multi-unit OperationCancelling a base unit Cancelling a handsetSelecting a base unit Setting the selected handsets to ring before all handsets ring Setting all or selected handsets to ringSetting all handsets to ring Setting the selected handsets to ring2 Handset Intercom between handsetsTransferring calls between handsets/ Conference call 1 HandsetUseful Information TroubleshootingThe battery should be charging but the battery icon does not change A busy tone is heard when C or s is pressedCaller information is not displayed Answering system KX-TCD445 onlyThe handset beeps intermittently and/or 074 flashes I fully charged the batteries, but 074 still flashesDimensions, Handset Approx. 143 mm x 48 mm x 32 mm RF Transmission Power Approx. 250 mWPower consumption, Base unit Standby Dimensions, Base unit Approx. 58 mm x 128 mm x 105 mmIndex IndexW Wall mounting V Volume Receiver 10 Ringer Base unit 22 Ringer Handset 18 SpeakerPage PQQX14164ZA FT0504FD0 For your future referenceCustomer Support Centre Tel. No. 09 272 Sales Department Manufacturer