Panasonic KX-TG6821SA Changing the base unit PIN Personal Identification Number, Dect repeater

Page 29

Programming

1MN#256

2Enter the base unit PIN (default: “0000”). R If you forget your PIN, contact an

authorised service centre.

3Select the handsets to be restricted by pressing 1 to 2.

R All handsets registered to the base unit are displayed.

R “” is displayed next to the selected handset numbers.

R To cancel a selected handset, press the same dial key again. “” disappears.

4MOKN

5Select a memory location by pressing 1 to 6. a MOKN

6Enter the phone number or area code to be restricted (8 digits max.). a MOKN a MeN

R To erase a restricted number, press MCN.

Changing the base unit PIN (Personal Identification Number)

Important:

RIf you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, contact an authorised service centre.

1MN#132

2Enter the current 4-digit base unit PIN (default: “0000”).

3Enter the new 4-digit base unit PIN. a

MOKN

4MbN: “Yes” a MOKN a MeN

Increasing the range of the base unit

You can increase the signal range of the base unit by using a DECT repeater. Please use only the Panasonic DECT repeater noted on page 4. Contact your Panasonic dealer for details.

Important:

RBefore registering the repeater to this base unit, you must turn the repeater mode on.

RDo not use more than one repeater at a time.

Setting the repeater mode

1MN#138

2MbN: Select the desired setting. a MOKN a MeN

Note:

RAfter turning the repeater mode on or off,

may be displayed on the handset momentarily. This is normal and the

handset can be used once is displayed.

Registering the DECT repeater (KX-A405) to the base unit

Note:

RPlease use a repeater that has not yet been registered to another unit. If the repeater is registered to another unit, deregister it first, referring to the Installation Guide for the DECT repeater.

1Base unit:

Proceed with the operation for your model.

n KX-TG6811 series: page 3 Press and hold MN for about 5 seconds. (No registration tone)

n KX-TG6821 series: page 3 Press and hold MN for about 5 seconds, until the registration tone sounds.

R The next step must be completed within 90 seconds.

2DECT repeater:

Connect the AC adaptor, then wait until

the indicator and indicator light green.

3Base unit:

To exit the registration mode, press MN. R The registration tone stops.

(KX-TG6821 series: page 3)

29

TG68xxSA(en)_0619_ver011.pdf 29

2013/06/19 17:43:17

Image 29

Contents Thank you for purchasing a Panasonic product Digital Cordless PhoneDigital Cordless Answering System Table of Contents Model composition Feature differencesSupplied accessories Accessory informationAdditional/replacement accessories Accessory itemFor your safety Battery Important safety instructionsFor best performance Base unit location/avoiding noiseRoutine care SpecificationsOther information Battery installation Setting upConnections Correct IncorrectBattery level Battery chargingIcon Battery level Operation Operating timeBase unit ControlsHandset Handset display items DisplayGreeting Only is LineDisplay language Turning the power on/offInitial settings Using the Smart Function Key NR key Dialling modeSmart Function Key NR key Date and timeSetting the Smart Function Key One touch eco modeAnswering calls Making callsUseful features during a call Key lock Power back-up operationHandset noise reduction NR key Handset equalizerWhen only 1 handset is registered Making calls during a power failureContinuing a call during a power failure Phonebook MbN Phonebook a Mokn Speed dial Display the menu tree and direct command code table Programmable settingsMemo Alarm Alarm1-3 Once Settings Number of Rings *2 2-7 RingsTime Adjustment *2, *4 Caller ID New Message Alert *2 Outgoing CallHandset Ringer Volume Ringer Setup Ringer VolumeNight Mode On/Off Night ModeMsec # 160 msec Privacy Mode *2, *5, *12 Line Setup Dial Mode *2 PulseRepeater Mode *2 Power Failure Cancel Register *3Special programming AlarmOn 0 Off #173 Main menu Caller Barred*2, *13Turning night mode on/off Night modeSetting the ring delay Changing the start and end timeChanging the handset name Setting call restrictionIncoming call barring Caller ID subscribers only MeNChanging the base unit PIN Personal Identification Number Setting the repeater modeIncreasing the range of the base unit Dect repeaterCaller ID features Using Caller ID serviceCaller list Viewing the caller list and calling backErasing selected caller information Editing a caller’s phone number before calling backErasing all caller information Storing caller information to the phonebookTurning the answering system on/off Answering systemGreeting message Memory capacity including your greeting messageMeN Using a pre-recorded greeting message Listening to messages using the base unitRecording your greeting message Operating the answering system during playbackErasing all messages Listening to messages using the handsetOperating the answering system Calling back Caller ID subscribers onlyNew message alert by a call Advanced new message alerting featuresAudible message alert Using the answering system remotely Remote access codeRemote commands Remote operationFor voice mail service subscribers Answering system settingsTurning on the answering system remotely Number of rings before the unit answers a callSelecting Greeting Only Caller’s recording timeVoice mail service Transferring calls, conference calls IntercomHandset locator Character entry modes Character entryCyrillic character table Extended 1 character tableExtended 2 character table Display message Error messagesCause/solution General use TroubleshootingProblem Making/answering calls, intercom Programmable settingsBattery recharge Answering system Caller IDRegistering a handset to the base unit Liquid damageDeregistering a handset Index 2013/06/19 2013/06/19 For your future reference