Compaq 340622-002 manual Microsoft Windows NT, 6Installing the Software Drivers

Page 27

3-6Installing the Software Drivers

Microsoft Windows NT

The following table provides information on identifying appropriate drivers for Compaq SCSI controllers:

 

Table 3-2

 

Microsoft Windows 95

 

 

Controller

Software Driver Information

32-Bit Fast-SCSI-2 Controller

Refer to W95READ.HLP for the list of controllers

or 32-Bit Fast-Wide SCSI-2

supported on Microsoft Windows 95.

 

Controller

 

or Wide-Ultra SCSI Controller

 

 

 

 

 

IMPORTANT: If the SCSI controller to which your tape drive is attached was not present during your initial Windows 95 installation, install the SCSI device driver for the controller before installing the tape class driver.

Compaq SLR Tape Drive User Guide

Image 27
Contents SLR Tape Drive Compaq SLR Tape Drive User Guide Contents Installing the Software Drivers Appendix B Appendix C Vii About This Guide Text ConventionsViii About This Guide Symbols in TextGetting Help Compaq Web SiteIx About This Guide Telephone NumbersData Compression OverviewDrive Capacity Drive Performance2Overview Cartridge Specifications Compatibility, and FormatsProjected Duty Cycle Supported QIC formatsKit Contents Controller Chapter Drive InstallationRequirements ToolsSetting the Drive’s Scsi ID 2Drive InstallationPreparing the System 3Drive Installation Locating the Jumper BlockSelecting the Scsi ID Installing the Drive 4Drive InstallationSelecting the Scsi ID 5Drive Installation 6Drive Installation Installing the Drive With Rails7Drive Installation Installing the Drive Without Rails8Drive Installation Installing the Power Cable ExtenderCompleting the Installation 9Drive InstallationReassembling the System Installing the Software Drivers 1Installing the Software DriversObtaining the Drivers 2Installing the Software Drivers 3Installing the Software Drivers Novell IntranetWare/NetWareNovell IntranetWare/NetWare Aspi Support 4Installing the Software DriversCompaq Aspi Support 5Installing the Software DriversMicrosoft Windows NT 6Installing the Software DriversMicrosoft Windows 7Installing the Software DriversSCO OpenServer 8Installing the Software Drivers9Installing the Software Drivers SCO UnixWareSCO UnixWare IBM OS/2 10Installing the Software Drivers11Installing the Software Drivers SunSoft SolarisSunSoft Solaris 12Installing the Software Drivers Banyan VinesBanyan Vines 1Operating and Cleaning the Drive Chapter Operating and Cleaning DriveMeaning of Front Panel LED Display Front Panel Indicators2Operating and Cleaning the Drive OperationFront Panel Controls 3Operating and Cleaning the DriveHandling and Storing a Cartridge 4Operating and Cleaning the DriveLoading and Unloading a Cartridge 5Operating and Cleaning the DriveRetensioning a Cartridge 6Operating and Cleaning the Drive7Operating and Cleaning the Drive Cleaning GuidelinesUsing the Cartridge’s Write Protect Switch Cleaning Procedure8Operating and Cleaning the Drive 1Troubleshooting TroubleshootingSoftware Checks Quick Checklist2Troubleshooting Hardware ChecksTroubleshooting Flowchart 3TroubleshootingCompleting the System Configuration Worksheet 4TroubleshootingChecking for Resource Conflicts 5Troubleshooting Checking Power to the Drive 6TroubleshootingChecking the Drive Sense Codes Troubleshooting in Novell IntranetWare/NetWare7Troubleshooting Checking SoftwareTroubleshooting in Microsoft Windows NT Using the System Event Log8Troubleshooting A typical Event Viewer display 9TroubleshootingChange from Bytes to Words 10TroubleshootingVerifying the software drivers 11TroubleshootingTroubleshooting in SCO OpenServer Troubleshooting in IBM OS/212Troubleshooting 13Troubleshooting Troubleshooting in Banyan VinesAccessing the System Log from Operator menu Accessing the System Log from Operate utilityTroubleshooting in ArcServe for NT 14TroubleshootingArcServe for NT Logs A typical Activity Log display 15TroubleshootingA typical Tape Engine Log display 16Troubleshooting17Troubleshooting Troubleshooting with ArcServe for NetWareGeneric Error Report 18TroubleshootingVerifying Recent Changes 19TroubleshootingCorrecting Intermittent Failures 20Troubleshooting21Troubleshooting Upgrading the FirmwareUpgrading the Firmware with a Cartridge 22Troubleshooting Upgrading the Firmware By using the Option ROMPaqSelect an Image screen 23TroubleshootingCreating a ROMPaq diskette Upgrading the firmwareFor Further Assistance 24TroubleshootingRegulatory Compliance Notices Federal Communications Commission Notice1Regulatory Compliance Notices 2Regulatory Compliance Notices Class B EquipmentCables Canadian Notice Avis CanadienEuropean Union Notice Modifications4Regulatory Compliance Notices Japanese Notice Australian NoticeAppendix B Electrostatic Discharge Grounding Methods1Electrostatic 2Electrostatic Drive Configuration Options 1Drive Configuration OptionsLocating the Jumper Block Identifying the Jumpers 2Drive Configuration Options3Drive Configuration Options Selecting the Scsi IDTable C-1 Selecting the Scsi ID Enabling/Disabling Bus Parity TestingConfiguring the Scsi ID in a SCO OpenServer environment 4Drive Configuration OptionsIndex IBM OS/2 Scsi ID Index