Lincoln Electric SVM188-A service manual Control Board Test

Page 59

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-19

TROUBLESHOOTING AND REPAIR

F-19

CONTROL BOARD TEST

WARNING

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed throughout this manual.

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department for electrical trou- bleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This procedure will help to determine if the Control Board is functioning properly. The LEDs (Light Emitting Diodes) will help to determine if the Control Board is receiving the correct signals and sending the proper signal to the Firing Board.

MATERIALS NEEDED

Misc. Hand Tools

Multimeter

Wiring Diagram or Machine Schematic

DC-600

Image 59

Contents DC-600 ISAFETYi Can be dangerous SafetyElectric Shock can kill Fumes and GasesFor Electrically Powered equipmentSûreté Pour Soudage a L’Arc Précautions DE SûretéElectromagnetic Compatibility EMC Safety Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications DC-600 InstallationSelect Proper Location Safety PrecautionsElectric Shock can Kill Ground Connection Fuse and Wire SizesElectrical Input Connections Connection for Highest Rating Plate VOLTAGE, 50 or 60 HZ Reconnect ProcedureConnection for 440 Volts 50 or 60 HZ V 60HZ See Machine Rating Plate for Required Input Supply Voltage Connections Output ConnectionsELECTRODE, Work and #21 Lead Terminal Strip 2 T.S.2 Auxiliary Power Control ConnectionsTerminal Strip 1 T.S.1 DC-600 Table of Contents Operation Section Operation Safety PrecautionsRecommended Processes and Equipment Design Features AdvantagesGeneral Description Output Control Output Voltage Current Meanings of Graphical Symbols on Case FrontOFF Input Power Welding CapabilityControls and Settings Meaning of Graphical Symbol for Ground CON- NectionOVERLOAD, OVERCURRENT, and Fault Protection Auxiliary Power in MS-RECEPTACLEOperating Steps Remote Control of Machine OperationWelding Procedure Recommendations Remote NA-3 Automatic Wire FeederLN-7 and Other Constant Wire Feeders LN-8 or LN-9 SEMI-AUTOMATIC Wire FeederDC-600 Table of Contents Accessories Section Field Installed Options AccessoriesWire Feeders and Tractors Factory or Field Installed OptionsFigure C.2 MULTI-PROCESS Switch Cable Connections Accessories Table of Contents Maintenance Section Routine and Periodic Maintenance MaintenanceSafety Precautions Electric Shock can Kill 1TABLE of CONTENTS-THEORY of Operation Section E-1 Input Circuit and Main TRANS- Former Theory of OperationFiring Board Firing CIRCUIT, Control CIR- Cuit and RectificationRectification Thermal Protection SCR Operation DC-600 1TABLE of Contents Troubleshooting and Repair F-1 HOW to USE Troubleshooting Guide 2TROUBLESHOOTING and REPAIRF-2PC Board Troubleshooting Procedures Troubleshooting and RepairControl Feeder. See Protective Devices Check all three phase input Output Control J1,Pin2. See Wiring Diagram Wiring Diagram Materials Needed PC Board Troubleshooting GuideTest Description PC Board Troubleshooting Guide Figure F.2 Control Board LEDs Control BoardDC-600 Internal Trigger Circuit Test Internal Trigger Circuit Test Procedure75 76 Internal Trigger Circuit TestDC-600 Firing Board Test Firing Board Test Control Board Test Figure F.7 Control Board Control Board TestMain Transformer Voltage Test Figure F.8 Input Contactor and Reconnect Panel Main Transformer Voltage TestFigure F.9 Transformer Secondaries Main Transformer Voltage Test Control Transformer Test Control Transformer Test ProcedureInput Contactor Test Voltage Test Input Contactor TestSCR Bridge Test SCR Bridge Test Anode Cathode Remove Insulating PaintActive Test Scope Settings Maximum Output Setting no Load Minimum Output Setting no Load 35TROUBLESHOOTING and REPAIRF-35 2V/Div Volts DC-600 Input Contactor CR1 CLEANING/REPLACEMENT Contactor Replacement Procedure Input Contactor CLEANING/REPLACEMENT ProcedureCleaning Procedure SCR Rectifier Bridge Removal and Replacement Procedure SCR Rectifier Bridge 42TROUBLESHOOTING and REPAIRF-42Removal and Replacement Procedure Removal ProcedureInsulator Lock Washer Plain Washer Output Snubber Lead Replacement ProcedureDC-600 Main Transformer and Choke Removal and Replacement Main Transformer and Choke Removal and ReplacementRemoval Procedure Weld Maximum Open Circuit Voltages Input Idle Amps and WattsDC-600 Table of Contents Diagram Section Electrical Diagrams Wiring Diagram 230/460/575 Volt Machines G3506-1 Schematic Complete Machine G3575 Schematic Control PC Board G3408-1 Control PC Board Assembly G3409-1 Schematic Firing PC Board G3741-1