Lincoln Electric SVM188-A service manual Output Connections, ELECTRODE, Work and #21 Lead

Page 16

Return to Section TOC

Section TOC

Return to Master TOC

Master TOC

A-8

INSTALLATION

A-8

OUTPUT CONNECTIONS

See Table A.1 for recommended DC-600 cable sizes for combined lengths of electrode and work cables.

TABLE A.1

DC-600 Cable Sizes for Combined Lengths of Copper Electrode and Work Cable

at 100% Duty Cycle

ELECTRODE, WORK AND #21 LEAD

Cable Length	Parallel Cables	Cable Size

Lengths up to 150 ft. (46m)	2	1/0 (53mm2)

150 ft.(46m) to 200 ft (61m)	2	2/0 (67mm2)

200 ft.(61m) to 250 ft.(76m)	2	3/0 (85mm2)

Return to

Return to Section TOC

Return to Section TOC

Return to

Return to Master TOC

Return to Master TOC

CONNECTIONS

A. Connect Electrode and Work Leads to Output Terminals.

1.Set the ON/OFF toggle switch to OFF.

2.Locate the retractable strain relief loops directly below the output terminals in the lower right and lower left corners of the Case Front Assembly. See Figure A.9.

3.Pull out the retractable strain relief loops.

4.Insert the electrode lead through the loop directly below the desired polarity (positive or negative). Pull through enough cable to reach the output terminals.

5.Connect electrode lead to the desired terminal (positive/negative).

6.Tighten the output terminal nut with a wrench.

7.Connect the work lead to the other output terminal following steps 4-6.

FIGURE A.9 - Output Terminals.

B. Connect #21 Work Sense Lead to Proper Terminal

There are two work sense lead connection points (+21 and -21) on terminal strip (T.S.2) located behind the hinged access panel on the right side of the case front. See 14 Pin MS Type Receptacle section or Terminal Strip Section for connection procedure.

DC-600

Image 16

Contents DC-600 ISAFETYi Safety Electric Shock can killFumes and Gases Can be dangerousPowered equipment For ElectricallyPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcElectromagnetic Compatibility EMC Safety Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications DC-600Electric Shock can Kill Safety PrecautionsSelect Proper Location Electrical Input Connections Fuse and Wire SizesGround Connection Reconnect Procedure Connection for Highest Rating Plate VOLTAGE, 50 or 60 HZConnection for 440 Volts 50 or 60 HZ V 60HZ See Machine Rating Plate for Required Input Supply Voltage ELECTRODE, Work and #21 Lead Output ConnectionsConnections Terminal Strip 1 T.S.1 Auxiliary Power Control ConnectionsTerminal Strip 2 T.S.2 DC-600 Table of Contents Operation Section Safety Precautions OperationGeneral Description Design Features AdvantagesRecommended Processes and Equipment Meanings of Graphical Symbols on Case Front OFF Input PowerWelding Capability Output Control Output Voltage CurrentMeaning of Graphical Symbol for Ground CON- Nection Controls and SettingsAuxiliary Power in MS-RECEPTACLE OVERLOAD, OVERCURRENT, and Fault ProtectionWelding Procedure Recommendations Remote Control of Machine OperationOperating Steps NA-3 Automatic Wire Feeder RemoteLN-8 or LN-9 SEMI-AUTOMATIC Wire Feeder LN-7 and Other Constant Wire FeedersDC-600 Table of Contents Accessories Section Accessories Wire Feeders and TractorsFactory or Field Installed Options Field Installed OptionsFigure C.2 MULTI-PROCESS Switch Cable Connections Accessories Table of Contents Maintenance Section Safety Precautions Electric Shock can Kill MaintenanceRoutine and Periodic Maintenance 1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Input Circuit and Main TRANS- FormerRectification Firing CIRCUIT, Control CIR- Cuit and RectificationFiring Board Thermal Protection SCR Operation DC-600 1TABLE of Contents Troubleshooting and Repair F-1 2TROUBLESHOOTING and REPAIRF-2 HOW to USE Troubleshooting GuideTroubleshooting and Repair PC Board Troubleshooting ProceduresControl Feeder. See Protective Devices Check all three phase input Output Control J1,Pin2. See Wiring Diagram Wiring Diagram Test Description PC Board Troubleshooting GuideMaterials Needed PC Board Troubleshooting Guide Control Board Figure F.2 Control Board LEDsDC-600 Internal Trigger Circuit Test Procedure Internal Trigger Circuit TestInternal Trigger Circuit Test 75 76DC-600 Firing Board Test Firing Board Test Control Board Test Control Board Test Figure F.7 Control BoardMain Transformer Voltage Test Main Transformer Voltage Test Figure F.8 Input Contactor and Reconnect PanelFigure F.9 Transformer Secondaries Main Transformer Voltage Test Control Transformer Test Procedure Control Transformer TestInput Contactor Test Input Contactor Test Voltage TestSCR Bridge Test Anode Cathode Remove Insulating Paint SCR Bridge TestActive Test Scope Settings Maximum Output Setting no Load Minimum Output Setting no Load 35TROUBLESHOOTING and REPAIRF-35 2V/Div Volts DC-600 Input Contactor CR1 CLEANING/REPLACEMENT Cleaning Procedure Input Contactor CLEANING/REPLACEMENT ProcedureContactor Replacement Procedure SCR Rectifier Bridge Removal and Replacement Procedure 42TROUBLESHOOTING and REPAIRF-42 Removal and Replacement ProcedureRemoval Procedure SCR Rectifier BridgeReplacement Procedure Insulator Lock Washer Plain Washer Output Snubber LeadDC-600 Main Transformer and Choke Removal and Replacement Removal and Replacement Main Transformer and ChokeRemoval Procedure Weld Input Idle Amps and Watts Maximum Open Circuit VoltagesDC-600 Table of Contents Diagram Section Electrical Diagrams Wiring Diagram 230/460/575 Volt Machines G3506-1 Schematic Complete Machine G3575 Schematic Control PC Board G3408-1 Control PC Board Assembly G3409-1 Schematic Firing PC Board G3741-1